EPSON AcuLaser C1100
Class
Panel Messaeg
Service Req E527
Service Req E530
Service Req E533
Service Req E537
Service Req E542
Service Req E546
Service Req E547
Service Req E998
TROUBLESHOOTING
Table 3-3. List of Service Request
Deve Home Position Sensor Error
PWBA MCU could not receive signals output from Rotary Home Position Sensor within the specified time after rotation of Rotary
Developer.
Humidity Sensor Error
When the Input from SENSOR HUM & TEMP is out of specification.
Temp Sensor Error
SENSOR HUM & TEMP detected a temperature below -7°C or over 55°C.
Fuser Fail
• Control Thermistor detected a temperature exceeding the specified temperature.
Safety Thermistor detected a temperature exceeding the specified temperature.
• The Control Thermistor did not detect a Ready even though the specified time elapsed from Main Lamp ON at Warm Up.
• The Main Lamp continues to stay lit even after time specified for the Main Lamp elapsed after the Control Thermistor detected a
Ready.
• The Control Thermistor detected a temperature below the specified temperature even after the specified time elapsed from Main
Lamp ON at Warm Up.
• The latch lever of FUSER ASSY is set incorrectly.
IBT CLN Fail
SENSOR IBT RETRACT cannot detect Advance/Retract of CAM ASSY-IBT CL.
Duplex Motor Failure
The MOTOR ASSY DUP (Lower Roll Motor) or MOTOR ASSY DUP INV (Upper Roll Motor) of Duplex is not rotating at the
specified speed.
Feed Motor Failure
DRIVE ASSY FEED (Feed Motor) of the Feeder is not rotating at the specified speed.
Engine Communication Error
Acommunication error between the controller and the PWBA MCU via the video I/F occured
FIP according to the printer message
Description
Revision B
See FIP
45 (p.198)
55 (p.211)
54 (p.211)
53 (p.210)
58 (p.216)
57 (p.214)
56 (p.212)
78 (p.237)
131
The most common error codes.
Error | |
---|---|
E516 | Description: Communication Error Duplex — A communication error occurred between PWBA MCU and Duplex. |
E537 | Description: Fuser Fail — Control Thermistor detected a temperature exceeding the specified temperature. Safety Thermistor detected a temperature exceeding the specified temperature. — The Control Thermistor did not detect a Ready even though the specif |
C0017 •.C0258 | Description: Service Req C0017 CPU error (undefined interruption) Service Req C0081 CPU error (TLB modification exception) Service Req C0082 CPU error (TLB miss exception [Load/Fetch]) Service Req C0083 CPU error (TLB miss exception [Store]) Service Req |
E517 | Description: Communication Error Feeder — A communication error occurred between PWBA MCU and Feeder. |
E542 | Description: IBT CLN Fail — SENSOR IBT RETRACT cannot detect Advance/Retract of CAM ASSY-IBT CL. |
E516 | Description: Communication Error Duplex — A communication error occurred between PWBA MCU and Duplex. |
E537 | Description: Fuser Fail — Control Thermistor detected a temperature exceeding the specified temperature. Safety Thermistor detected a temperature exceeding the specified temperature. — The Control Thermistor did not detect a Ready even though the specif |
C0017 •.C0258 | Description: Service Req C0017 CPU error (undefined interruption) Service Req C0081 CPU error (TLB modification exception) Service Req C0082 CPU error (TLB miss exception [Load/Fetch]) Service Req C0083 CPU error (TLB miss exception [Store]) Service Req |
E517 | Description: Communication Error Feeder — A communication error occurred between PWBA MCU and Feeder. |
E542 | Description: IBT CLN Fail — SENSOR IBT RETRACT cannot detect Advance/Retract of CAM ASSY-IBT CL. |
[Fix] Epson C1100 Service Required e537 – one of the common error in Epson C1100 is Serv Req E537. This error is also common in Aculaser C1100, CX11N, CX21N and all variants. To fix this error is just turn off the printer, wait around 30 seconds and turn on again. if the error is not lost please follow the following tutorial.
Very often Epson printers have a strange error message like one example is Service Required e537. The “Req E537 server” error message printer usually occurs because the fusher fails to warm up the required temperature. This could result from a paper mis-feed, the fuser being improperly seated, ecological variables or an issue with the fuser itself.
Solution 1
Here we provide some solutions that you can practice for Epson C1100 printer can be reused properly and can print your document files. First check for a paper jam or other blockage in the fuser device, and reseat it. Power off the printer, leave it for around 30 seconds and then power it on once more. This could clear the error. If not, check out additionally.
When the printer has actually been in use, the fuser device and surrounding locations may be extremely hot. Wait 20 minutes or even more for the fuser device to cool, and make sure not to touch the fuser rollers themselves. You could discover additional safety and repairing details in your customer guide, available from the Epson web site.
See image below to fix.
In the final steps, close the cover and try to print other documents. If it’s doesn’t work, turn off the printer than turn on again.
Solution 2
Check that the paper being utilized appropriates for a printer and within specification.
These are the sustained paper kinds and weights for typical media kinds, ranked in g/m2. The weight must be kept in mind on your paper’s product packaging. If unclear, consult your distributor:
Paper Type | Weight Range | Load Paper In |
---|---|---|
Plain paper | 64 to 80 g/m2 | Any paper tray |
Semi-thick | 81 to 105 g/m2 | Any paper tray if Epson media, otherwise MP Tray |
Thick | 106 to 163 g/m2 | MP Tray Only |
Extra thick | 164 to 210 g/m2 | MP Tray Only |
Coated | 105 to 210 g/m2 | MP Tray Only |
Inkjet paper, specifically photo or shiny media, is not developed to hold up against the warmth of a warm fuser system and could jam or perhaps thaw inside the printer.
See among the Related Articles or your individual overview for additional info on right paper storage space, suitable paper density setups, making use of the right paper tray and suggestions on printing on unique media such as envelopes, openness and tags.
Solution 3
If it is especially cool, or if the printer is near to an open home window, it could not have the ability to heat up. Relocate the system to a warmer setting and examination it once again.
Control Thermistor discovered a temperature level surpassing the defined temperature level. Security Thermistor discovered a temperature level surpassing the defined temperature level.? The Control Thermistor identified a temperature level listed below the defined temperature level also after the defined time expired from Main Lamp ON at Warm Up?
You may also like [Fix] Epson Aculaser C1100 Error E511