Frenic 5000g11 коды ошибок

8

Error messages are displayed on the Display screen as follows: «No. : Device Name: Error Message (Error

Occurrence Area)». Each description is shown below.

Item

No.

Device Name

Error Message

Error Occurrence Area

Example of an Error Messages

«RHAA035: PLC1: Error has been responded for device write command (Error Code: 2 [02H])»

• Refer to your External Device manual for details on received error codes.

• Refer to «Display-related errors» in «Maintenance/Troubleshooting Guide» for details on the

Error Codes Unique to External Device

Error Code

4AH

4BH

4CH

4DH

4EH

4FH

GP-Pro EX Device/PLC Connection Manual

Error number.

Name of the External Device where an error has occurred. Device/PLC name is the title of

the External Device set with GP-Pro EX. (Initial value [PLC1])

Displays messages related to an error that has occurred.

Displays the IP address or device address of the External Device where an error has

occurred, or error codes received from the External Device.

• IP addresses are displayed as «IP address (Decimal): MAC address (Hex)».

• Device addresses are displayed as «Address: Device address».

• Received error codes are displayed as «Decimal [Hex]».

error messages common to the driver.

Format error

• The characters of the transmission request are incorrect.

• The last character of the message is not in the specified position.

Command error

• A command that does not exist was transmitted.

*1

Link priority error

• A frequency command, PID command, or change command of the run command

(writing request to S01, S05, S06, and S13) are sent through the communication route

other than that specified with H30.

Unauthorized write error

• An attempt was made to write another function data during writing from link option.

Function code error

• A function code that does not exist was requested.

Write disabled error

• An attempt was made during operation to write the function code for write disabled or

for write disabled during operation.

Description

Description

110

INVERTER SIO Driver

continued to next page

9-15

Data format [21]

Auto tuning

15

14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

0 0 0 0 0 0

REV

FWD

Data

portion

0: Without forward rotation command
1: With forward rotation command.
0: Without reverse rotation command.
1: With reverse rotation command.

Example) If P04 (motor 1 auto — tuning)=1: Forward rotation

0000 0001 0000 0001

b

=0101

H

9-4-8 Communication Errors

Exception Response
When the inverter receives a message that does not contain communication errors but the message can not
be processed, the inverter will return an exception response. The exception response contains an error
sub-code in the data field that represents the problem.

Exception Response Errors

Sub-Code Name

Causes

1

Illegal Function

Received RTU Function other than 03, 06 or 16

2

Illegal Data Address

• The starting parameter address is an unused inverter parameter.
• The starting parameter address plus the offset refers to inverter

parameter greater than the last parameter in a Function Code sort.

• The number of registers is greater than 16.

3

Illegal Data Value

Data contains an out of range value for an inverter parameter

7

Negative Acknowledge

• Requested data cannot be changed while the inverter is running.
• The inverter parameter function is owned by the network interface

option card and cannot be changed.

Communication errors
Communication errors occur when the inverter receives an invalid message. The inverter will not return a
response to a communication error. A code that represents the last communication error is stored in
inverter parameter M26. Typical communication message errors include parity, framing, and CRC errors.

Подновлю тему . Станок САК 3665d . Китаец континентальный . Тормозной резистор есть , родной , от Fuji . DC реактора нет. Полазил по клавишам программатора (панели) 

привода . Любопытная картина . Ошибка вылетает при выходе частотника на частоту 22 Гц , напряжение на двигатель менее 150 В , нагрузки на двигателе реальной  нет , 10%

по контролю момента , нагрузка шпинделя на мониторе Fanuc вообще не просматривается , контроль оборотов система ведёт . Единственное , что — контроль величины

выпрямленного напряжения . По той-же панели 760В при 20 об/мин , на 330 об/мин ( а в ошибку уходит на 350 ) подпросаживается до 750.( питание 3х380В , в реале вечером

3х390В ). Стрелочным встать не удалось ,завтра попробую , цифровик дешёвый — ересь показывает . Параметры на английском погрызу .Спасибо всем .

Изменено 01.11.2021 18:16 пользователем sermor