Samsung ml 1520p выдает ошибку

– Compatible Printer model: Samsung ML1520
– Samsung ML1520 Error Codes with quick guides:

• Code: 01
• Display: Wrong Print Position
• Description: Printing begins at wrong position on the paper.
• Causes: Wrong sense time caused by defective feed sensor actuator.
• Troubleshooting Guides: Replace the defective actuator

• Code: 02
• Display: JAM 0
• Description: 1. Paper is not exited from the cassette. 2. Jam-0 occurs if the paper feeds into the printer.
• Causes: 1. Check the Solenoid by using DCU diagnostic mode 06. 2. Check if the pad is loose due to bad sealing of the side-pad. 3. Check the surface of the roller-pickup for foreign matter. 4. If continuous clusters occur, check whether the assembly slot between shaft-pickup and housing-pickup become open or is broken away. 5. If the paper feeds into the printer rand Jam 0 occurs, perform DCU to check feed-sensor of the engine board.
• Troubleshooting Guides: 1. Replace the solenoid. 2. Replace the side-pad Assembly L or R, if necessary. 3. Clean with soft cloth dampened with IPA(Isopropyl Alcohol) or water. 4. Replace the Housing-Pickup and/or Shaft-Pickup.

• Code: 03
• Display: JAM 1
• Description: 1. Recording paper is jammed in front of or inside the fuser. 2. Recording paper is stuck in the discharge roller and in the fuser just after passing through the Actuator-Feed.
• Causes: 1. If the recording paper is jammed in front of or inside the fuser. (Perform DCU diagnostic code of) 2. If the recording paper is stuck in the discharge roller and the fuser just after passing through the Actuator- Feed, Feed Actuator may be defective.
• Troubleshooting Guides: 1. Replace the SMPS. 2. Reassemble the Actuator-Feed and Spring-Actuator if the returning is bad.

• Code: 04
• Display: JAM 2
• Description: 1. Recording paper is jammed in front of or inside the fuser. 2. Recording paper is stuck in the discharge roller and in the fuser just after passing through the Actuator-Feed.
• Causes: 1. If the paper is completely fed out of the printer, but Jam 2 occurs : Exit sensor is defective. • After the paper is completely discharged, actuator Exit should return to the original position to shut the photo-sensor. Sometimes it takes longer hour than it should and does not return. 2. If the paper is rolled in the Fuser Roller: • This occurs when a Guide claw is broken away or transformed. • It occurs when the Spring of a Guide claw is broken away or transformed. • It occurs when the Heat-Roller or Pressure-Roller is seriously contaminated with the toner. 3. Paper is accordion in the fuser.
• Troubleshooting Guides: 1. Check if the exit sensor actuator is defective. • Check if the actuator exit is unformed (Check if the lever part is unformed in shape). • Check whether burrs occur in the assembly part of the actuator exit or not and if the actuator is smoothly operated. • Check if foreign matters and wire get caught in the actuator exit’s operation. 2. If the paper is stuck in the fuser : disassemble the fuser and remove the jammed paper, and clean the surface of the pressure roller with dry gauze. 3. Remove the jammed paper after disassembling the fuser : Clean the surface of the pressure roller with dry gauze. • Remove the toner particles stained on the rib. • Check the assemblage and performance of the exit.

• Code: 05
• Display: Multi-Feeding
• Description: Multiple sheets of paper are fed at once.
• Causes: 1. Solenoid malfunction(the solenoid does not work properly): Perform DCU mode : solenoid check 06. 2. Pad-Friction is contaminated with foreign matter.(oil…) 3. The face of paper is blended.
• Troubleshooting Guides: 1. Replace the solenoid if necessary. 2. Clean the pad friction with soft clothe dampened with IPA(Isopropyl Alcohol). 3. Use the smooth paper.

• Code: 06
• Display: Paper rolled in the fuser
• Description: If contaminated at intervals of 57mm on the back of a paper.
• Causes: 1. Contamination of the pressure roller. (Background, Hot off set)
• Troubleshooting Guides: 1. Disassemble the fuser, clean the area between the Heat-roller and Thermistor and remove the foreign matter of the pressure roller. 2. If background appears badly in the printing, fix it by referring to the solutions for background.

• Code: 07
• Display: OPC
• Description: Paper is rolled up in the OPC.
• Causes: 1. Paper is too much thin. 2. The face of paper is curled.
• Troubleshooting Guides: 1. Recommend to use normal paper. 2. How to remove the rolled paper in the OPC. • Remove the paper while turning the OPC against the ongoing direction. • Clean fingerprints on the OPC softly with soft cloth dampened with IPA(Isopropyl Alcohol) or tissue.

• Code: 08
• Display: All LEDs blinking (Fuser Error)
• Description: 1. All the lamps on the operator panel blink. 2. Gear of the fuser does not work and breaks away melt away. When printing, motor breaks away from its place due to defective fuser gear.
• Causes: 1. Check if the thermostat, AC wire and Heat Lamp is open. 2. Check if the thermistor sensor is in place. 3. Check if the heat lamp works properly. 4. Check if the overheat circuit works properly. 5. The fuser gear is defective due to melting away.
• Troubleshooting Guides: 1. If the thermostat is open replace the fuser and check following items. 2. If the thermistor sensor device is located deep in the sponge, replace the fuser. 3. Check if the circuit of overheat mode works properly. 4. Run DCU mode : Perform DCU diagnostic code 10.

• Code: 09
• Display: All LEDs blinking (Scan Error)
• Description: 1. All lamps on the operator panel blink.
• Causes: DCU Mode : Perform DCU diagnostic code 05. If the DCU error code 95 is displayed, replace LSU.
• Troubleshooting Guides: Replace LSU. If you cannot solve the problem after you replace LSU, replace the main board.

• Code: 10
• Display: Not function of the gear of the fuser due to melting away
• Description: The motor breaks away from its place due to gear melting away.
• Causes: DCU Mode : Check if the Error States ’60’ ’62’ ’68’ occur. Check the operation of Fuser Erasing Lamp On/Off with the Error Code Check -10-.
• Troubleshooting Guides: 1. Replace the Fuser. 2. Replace the Main Control board.

• Code: 11
• Display: Paper Empty
• Description: The paper lamp on the operator panel is on even when paper is loaded in the cassette.
• Causes: 1. Bending or deformation of the actuator of the paper sensor. 2. The function of the engine board is defective Perform DCU mode: Perform DCU diagnostic code 8.
• Troubleshooting Guides: 1. Replace the defective actuator. 2. Replace the engine board.

• Code: 12
• Display: Paper Empty without indication
• Description: The paper lamp on the operator panel does not come on when the paper cassette is empty.
• Causes: 1. Bending or deformation of the actuator of the paper sensor. 2. The function of the engine board is defective Perform. DCU mode : Perform DCU diagnostic code 8.
• Troubleshooting Guides: 1. Replace the defective actuator. 2. Replace the engine board.

Solve Samsung ML1520 Error codes

• Code: 13
• Display: Cover Open
• Description: The ERROR lamp is on even when the print cover is closed.
• Causes: 1. The Hook Lever in the top cover may be defective. 2. Check the connector (Engine Bfd-VPS) and circuit of the cover switch department in the Main Control board. Perform DCU mode : If Error state ’64’ occurs, Check the related codes of the Cover Open Error.
• Troubleshooting Guides: 1. Replace the hook lever, if defective. 2. Check the insertion of the Cover Open S/W Connect. 3. Replace the Main Control board or Cover Open S/W.

• Code: 14
• Display: No lamp on when the cover is open
• Description: The ERROR lamp does not come on even when the printer cover is open
• Causes: 1. Check the connector(CN8) and circuit of the cover switch department in the Main Control board. Perform DCU mode : If Error state ’64’ occurs, Check the related codes of the Cover Open Error
• Troubleshooting Guides: 1. Check the insertion of the Cover Open S/W Connect. 2. Replace the Main Control board or Cover Open S/W.

• Code: 15
• Display: Defective motor operation
• Description: Main motor is not driving when printing, and paper does not feed into the printer, resulting ‘Jam 0’.
• Causes: 1. Motor harness or sub PCB may be defective. 2. Perform DCU diagnostic code 00 and Check the motor operation.
• Troubleshooting Guides: 1. Check the motor harness, replace it, if defective. 2. Replace the SMPS, if necessary.

• Code: 16
• Display: No Power
• Description: When system power is turned on, all lamps on the operator panel do not come on.
• Causes: 1. Check if the power input and SMPS output are normal. 2. Check the inferiority of LED-Panel on the front-cover if the LED of Panel does not appear after normal warmingup.
• Troubleshooting Guides: 1. Replace the power supply cord or SMPS. 2. Replace the control board. 3. Replace the LED-panel.

• Code: 17
• Display: Vertical Line Getting Curved
• Description: When printing, vertical line gets curved.
• Causes: 1. If the supply of +24v is unstable in the Main Control board linking with LSU, check drive by DCU Mode: LSU Check -05- LSU Motor on.
• Troubleshooting Guides: 1. Replace LSU. 2. Replace the Main Control board.

– Get more information about Epson XP 15000 troubleshooting, click here

– Get more error code list with quick guide to fix printer product, click here

– About get help with reseting Epson inkpad or others, click here

Samsung printer reset software introduction:

Notes before resetting Samsung printer:

– Identify accurate version, serial and crum of Samsung printer.
– How to get Samsung printer model info: Click Here
– Before you continue with the reprogramming of the firmware, please make sure that the device is installed on your computer.
– It is very important that under no circumstances should you remove the chip from the cartridge while reprogramming the firmware. After you have succesfully reprogrammed the printer, remove the chip from the cartridge and store it somewhere safely (the chip – a key). In all cartridges which you are going to use in the printer, the chip has to be either removed or sealed. If you have accidently inserted a new cartridge without removing the chip, the device will be blocked. In order to unblock it, you can use the stored chip as a key which help you to unblock the printer.
– And make sure that any other devices (except mouse and keyboard), which are connected to your computer via USB or LPT ports are disconnected. It’s preferable that the computer is connected to the “UPS” (uninterruptible power source) device, because if during the reprogramming process the electricity source has any interruptions, then the reprogramming will be carried out with an error, which makes the device unable to work.
– This firmware will be installed directly to your printer. Before opening firmare link make sure that printer is turned on and connected to your computer and printer drivers are installed correctly.
Be aware that with the reprogramming of the firmware the manufacturer’s warranty goes lost!!

How To Run Firmware Fix Samsung printer

1. Connect the printer to the computer and turn it on.
2. Wait until the printer is ready for work.
3. Drag and drop *.hd to usbprns2.exe file.

4. The reprogramming process starts automatically.
5. Wait until the printer reprograms (10-20 minute) and restarts.
6. After that the reprogramming process is finished, restart the printer.

Contact us to get support with Samsung ML1520 Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
Or click here to get more ways.