DISCLAIMER: this information is for reference only. Fuel Moto does not offer technical support for diagnostic trouble codes. The following procedure will instruct in retrieving and clearing ECM Diagnostic Trouble Codes and TSM/TSSM codes through the Harley gauge cluster as well as a list of codes.
1- Turn Ignition switch to OFF & Run/Stop switch is to Run.
2- Push odometer reset button in & hold. For 2014 & newer touring models this will be the toggle switch on the left control mount.
3- Turn ignition switch to Ignition and release the odometer reset button. Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word «diag» should then appear.
4 — Push the odometer reset button once and you will see the selection menu «PSSPt» with the first P flashing.
5 — Each letter represents an area of the diagnostics module. The module that is flashing is the one you are going to check. To move from one letter (module) to the next, you push the odometer reset button one time. (from P to S to SP to t and back to P, etc.)
P = ECM/ICM(Electronic Control Module)[EFI] /Ignition Control Module[Carbureted])
S = TSM/TSSM (Turn Signal/ Security Module)
SP = speedometer
T = tachometer
6 — To get the DTC within an area of diagnostics, push and hold the odometer reset button in for 5 seconds and release. If there are any DTC’s the code will be displayed or the word «none» will appear if there are no DTC’s. Push the odometer reset button again to view additional codes if they exist.
7 — Record the codes.
8 — If DTC’s are not to be cleared, Press and release the odometer reset button. Part number of module will be displayed.
NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until ‘clear’ comes up. Release the odometer reset button. Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTC’s again by repeating steps 1 to 9. If the code is current it will reappear.
9 — Press and release the odometer reset button to continue to the next module.
10 — Turn Ignition switch to OFF.
On models not equipped with a tachometer «No Rsp» will appear when the tachometer identifier is selected.
«No Rsp» (no response) will also appear if the run/off switch is in the off position when doing this procedure.
—————————
HFSM = Hands Free Security Module
TSM = Turn signalmodule
DTC’s are designated by a P,C,B or U
P codes indicate issues monitored by ECM
C codes indicate an issue with ABS
B codes are set by Radio, Instruments and BCM
U codes indicate a communication problems with the modules
ABS – Anti-Lock Braking System
ACR – Automatic Compression Release
AFR – Air Fuel Ratio
AIS – Active Intake Solenoid
ATS – Air Temperature Sensor
BAS – Bank Angle Sensor
BCM – Body Control Module
CAN – Controller Area Network
CCM – Cruise Control Module
CKP – Crank Position Sensor
DLC – Datalink Connector
DTC – Diagnostic Trouble Codes
ECM – Electronic Control Module
ECT – Engine Coolant Temperature
ECU – Electronic Control Unit
EFI – Electronic Fuel Injection
EFP – Electronic Fuel Pump
ET – Engine Temperature sensor
FI – Fuel Injectors
FPR – Fuel Pressure regulator
H-DSSS – Harley-Davidson Smart Security System
HCU – Hydraulic Control Unit, ABS
HFSM – Hands Free Security Module
HO2S – Heated Oxygen Sensor
IAC – Idle Air Control actuator
IAT – Intake Air Temperature sensor
ICM – Ignition Control Module
IMAP – MAP + IAT in one unit
ISS – Ion Sensing System
JSS – Jiffy Stand Sensor
LHCM – Left Hand Control Module
MAP – Manifold Absolute Pressure Sensor
MHR – Right Hand Control Module
RCM – Reverse Control Module
TCA – Throttle Control Actuator
TGS – Twist Grip Sensor
TMAP – Intake Air Temperature / Manifold Absolute Pressure equipment
TPS – Throttle Position Sensor
TSM / TSSM – (Turn Signal / Turn Signal Security Module)
VE – Volume Efficiency
VIN – Vehicle identification number
VSS – Vehicle Speed Sensor
WSS – Wheel Speed Sensor
P0031 Front HO2S low/open
P0032 Front HO2S shorted/high
P0051 Rear HO2S low/open
P0052 Rear HO2S shorted/high
P0072 AAT sensor low
P0073 AAT sensor high/open
P0107 MAP sensor failed low/open
P0107 Map Sensor Open/Low
P0108 MAP sensor failed high/open port
P0112 IAT Voltage Low
P0113 IAT Voltage Open/High
P0117 ET Sensor Low
P0118 ET Sensor High
P0120 TPS1 Range Error
P0122 TPS1 Low
P0123 TPS2 High/Open
P0131 Front Oxygen Sensor Low / Engine Lean
P0132 Front Oxygen Sensor High / Engine Rich
P0134 Front Oxygen Sensor Inactive
P0151 Rear Oxygen Sensor Low / Engine Lean
P0152 Rear Oxygen Sensor High / Engine Rich
P0154 Rear Oxygen Sensor Inactive
P0220 TPS2 Range Error
P0222 TPS2 Low/Open
P0223 TPS2 High/Open
P0261 Front Injector Open/Low
P0262 Front Injector High
P0263 Rear Injector Open/Low
P0264 Rear Injector High
P0265 Rear injector shorted high
P0371 CKP sensor wrong number of pulses
P0373 CKP Sensor Intermittent
P0374 CKP Sensor Synch Error
P0444 Purge Solenoid Open/Low
P0445 Purge Solenoid High
P0501 VSS Sensor Low
P0502 VSS Sensor High/Open
P0503 VSS failed high
P0505 Idle speed control unstable
P0562 Battery/ECM Voltage Low
P0563 Battery/ECM Voltage High
P0572 Brake Switch Low
P0577 Cruise Control Input High
P0603 ECM EEPROM Memory Error
P0605 ECM FLASH Memory Error
P0641 5 Volt Reference 1 Out of Range
P0651 5 Volt Reference 2 Out of Range
P0691 Fan/cooling relay output low/open
P0692 Fan/cooling relay output high
P1001 System Relay Coil Open/Low
P1002 System Relay Coil High/Shorted
P1003 System relay contacts open
P1004 System Relay Contacts Closed
P1009 VTD Disabled Fuel Due to Incorrect Password
P1010 Missing Password
P1017 ET indicates overheating
P1019 ECT Difference (high temp)
P1270 TGS 2 A/D Validation Error
P1351 Front Ignition Coil Driver Open/Low
P1352 Front Ignition Coil Driver High/Shorted
P1353 Front Cylnder No Combustion
P1354 Rear Ignition Coil Driver Open/Low
P1355 Rear Ignition Coil Driver High/Shorted
P1356 Rear Cylinder No Combustion
P1357 Front Cylinder Combustion Intermittent
P1358 Rear Cylinder Combustion Intermittent
P1475 Exhaust Actuation Position Error
P1477 Exhaust Actuator Open/Low
P1478 Exhaust Actuator Shorted/High
P1501 Jiffy Stand Sensor Low
P1502 Jiffy Stand Sensor High
P1510 EFI Limited Performance Mode
P1511 EFI Power Management Mode
P1512 EFI Forced Idle Mode
P1514 ETC Air Flow Fault/Error
P1600 EFI Module Processor Internal Error / Watchdog Error
P1608 Loss of continuous battery
P1655 ACR solenoid low/open
P1656 ACR solenoid shorted high
P1691 Cooling fan left low/open
P1692 Cooling fan left shorted high
P1693 Cooling fan right low/open
P1694 Cooling fan right shorted high
P2100 EFI Motor Circuit Open
P2101 EFI Motor Circuit Range Performance (Actuation Error)
P2102 EFI Motor Circuit Low
P2103 EFI Motor Circuit High
P2105 EFI Forced engine shutdown
P2107 EFI Module Processor Internal Fault
P2119 EFI Motor Throttle Body RangePerformance
P2122 TGS1 Low/Open
P2123 TGS1 High
P2127 TGS2 Low/Open
P2128 TGS2 High
P2135 TPS Correlation Error
P2138 TGS Correlation Error (Twist grip sensor)
P2176 EFI Closed Position Not Learned
P2184 ECT sensor low
P2185 ECT sensor high
P2300 Ignition coil driver low/open (front)
P2301 Ignition coil driver shorted high (front)
P2303 Ignition coil driver low/open (rear)
P2304 Ignition coil driver shorted high (rear)
C0562 ABS voltage low
C0563 ABS voltage high
C1014 ABS ECU relay error
C1021 ABS front WSS always zero
C1023 ABS rear WSS always zero
C1025 ABS Front wheel speed intermittent
C1027 ABS rear wheel speed intermittent
C1029 ABS wheel speed difference too high
C1032 ABS Front wheel speed circuit open/shorted
C1034 ABS rear wheel speed circuit open/shorted
C1040 ABS pump/motor error
C1055 ABS ECU internal error
C1061 ABS front apply solenoid circuit open/high resistance
C1062 ABS front release solenoid circuit open/high resistance
C1065 ABS rear apply solenoid circuit open/high resistance
C1066 ABS rear release solenoid circuit open/high resistance
C1071 Rear prime valve error
C1072 Rear isolation valve error
C1073 Front isolation valve error
C1074 Front prime valve error
C1075 Front linked inlet valve error
C1076 Front linked outlet valve error
C1077 Front circuit pressure sensor error
C1078 Rear circuit pressure sensor error
C1081 Front master pressure sensor error
C1082 Front master pressure sensor offset error
C1083 Front wheel pressure sensor error
C1084 Front wheel pressure sensor offset error
C1085 Rear master pressure sensor error
C1086 Rear master pressure offset sensor error
C1087 Rear wheel pressure sensor error
C1088 Rear wheel pressure sensor offset error
C1089 Pressure sensor external supply error
C1159 ABS invalid stored VIN
C1178 ABS no VIN received from ECM
C1184 ABS invalid VIN from ECM
C1195 Wake up error
B0563 Battery Voltage High
B1103 LHCM Internal error
B1121(HFSM) Left Turn Output Open
B1121(TSM) Left Turn Output Fault
B1122(HFSM) Right Turn Output Open
B1122(TSM) Right Turn Output Fault
B1123(HFSM) Left Turn Output Short to Ground
B1124(HFSM) Right Turn Output Short to Ground
B1125(HFSM) Left Turn Output Short to Battery
B1126(HFSM) Right Turn Output Short to Battery
B1131(HFSM) Alarm Output Low
B1132(HFSM) Alarm Output High
B1134 Starter Output High
B1135 Accelerometer Failed
B1136(HFSM) Accelerometer Tip Test Error
B1141(HFSM) Ignition SwitchLow/Open
B1141(TSM) Ignition SwitchLow/Open
B1142 Smart Security System Internal Fault
B1143(HFSM) Security Antenna Short to Ground
B1144(HFSM) Security Antenna Short to Battery
B1145(HFSM) Security Antenna Open
B1151 Bank Angle Sensor(BAS) Short to Ground
B1152 Bank Angle Sensor(BAS) Short to Battery
B1153 Bank Angle Sensor(BAS) High
B1153 RHCM internal error
B1154 Clutch Switch Input Short to Ground
B1155 Neutral Switch Input Short to Battery
B1200 IM internal fault
B1210 Fuel level sender shorted low/open
B1211 Fuel level sender shorted high
B1212 Fuel signal low
B1213 Fuel signal high
B1300 Radio voltage high
B1301 Radio voltage low
B1302 Face plate home button stuck
B1303 Face plate favorite button stuck
B1304 Face plate navigation button stuck
B1305 Face plate power/mute button stuck
B1306 Rear hand controls shorted high
B1307 Rear hand controls shorted low
B1308 Rear volume up button stuck
B1309 Rear volume down button stuck
B1310 Rear mode button stuck
B1311 Rear PTT button stuck
B1312 Rear tune up button stuck
B1313 Rear tune down button stuck
B1314 LHCM VR button stuck
B1315 LHCM up button stuck
B1316 LHCM left button stuck
B1317 LHCM center button stuck
B1318 LHCM right button stuck
B1319 LHCM down button stuck
B1320 RHCM Info button stuck
B1321 RHCM up button stuck
B1322 RHCM left button stuck
B1323 RHCM center button stuck
B1324 RHCM right button stuck
B1325 RHCM down button stuck
B1326 RHCM CB squelch up button stuck
B1327 RHCM CB PTT button stuck
B1328 RHCM CB squelch down button stuck
B1329 Faceplate preset button 1 stuck
B1330 Faceplate preset button 2 stuck
B1331 Faceplate preset button 3 stuck
B1332 Faceplate preset button 4 stuck
B1333 Faceplate preset button 5 stuck
B1334 Faceplate preset button 6 stuck
B1335 Faceplate preset button 7 stuck
B1336 Faceplate preset button 8 stuck
B1337 Front left speaker shorted together
B1338 Front left speaker open
B1339 Front left speaker shorted low
B1340 Front left speaker shorted high
B1341 Rear left speaker shorted together
B1342 Rear left speaker open
B1343 Rear left speaker shorted low
B1344 Rear left speaker shorted high
B1345 Front right speaker shorted together
B1346 Front right speaker open
B1347 Front right speaker shorted low
B1348 Font right speaker shorted high
B1349 Rear right speaker shorted together
B1350 Rear right speaker open
B1351 Rear right speaker shorted low
B1352 Rear right speaker shorted high
B1353 Speaker offset DC output
B1354 GPS antenna open
B1355 GPS antenna shorted low
B1356 SDARS antenna open
B1357 SDARS antenna shorted
B1358 Front left headset shorted high
B1359 Front right headset shorted high
B1360 Front left headset shorted low
B1361 Front right headset shorted low
B1362 Rear left headset shorted high
B1363 Rear right headset shorted high
B1364 Rear left headset shorted low
B1365 Rear right headset shorted low
B1366 Internal thermal shutdown error
B1401 Amp voltage low
B1402 Amp voltage high
* Amp 1 Amp 2
B1403 Speaker offset DC output *
B1404 Internal thermal shutdown error *
B1405 EQ correlation error
B1406 Invalid or missing EQ
B1410 Channel 1 speaker open *
B1411 Channel 1 speaker shorted low *
B1412 Channel 1 speaker shorted high *
B1413 Channel 1 Speaker shorted together *
B1420 Channel 2 speaker open *
B1421 Channel 2 speaker shorted low *
B1422 Channel 2 speaker shorted high *
B1423 Channel 2 speaker shorted together *
B1430 Channel 3 speaker open *
B1431 Channel 3 speaker shorted low *
B1432 Channel 3 speaker shorted high *
B1433 Channel 3 speaker shorted together *
B1440 Channel 4 speaker open *
B1441 Channel 4 speaker shorted low *
B1442 Channel 4 speaker shorted high *
B1443 Channel 4 speaker shorted together *
B2102 System power output shorted high
B2103 System power output shorted low
B2104 System power output overloaded
B2106 L4 output open
B2107 L4 output shorted high
B2108 L4 output shorted low
B2109 L4 output overloaded
B2112 ACC output shorted high
B2113 ACC output shorted low
B2114 ACC output overloaded
B2116 Fuel pump output open
B2117 Fuel pump output shorted high
B2118 Fuel pump output shorted low
B2119 Fuel pump output overloaded
B2121 Starter output open
B2122 Starter output shorted high
B2123 Starter output shorted low
B2124 Starter output overloaded
B2127 E4 output shorted high
B2128 E4 output shorted low
B2129 E4 output overloaded
B2131 High beam output open
B2132 High beam output shorted high
B2133 High beam output shorted low
B2134 High beam output overloaded
B2136 Low beam output open
B2137 Low beam output shorted high
B2138 Low beam output shorted low
B2139 Low beam output overloaded
B2141 Left front turn signal output open
B2143 Left front turn signal output shorted low
B2144 Left front turn signal output overloaded
B2146 Right front turn signal output open
B2148 Right front turn signal output shorted low
B2149 Right front turn signal output overloaded
B2151 Left rear turn signal output open
B2153 Left rear turn signal output shorted low
B2154 Left rear turn signal output overloaded
B2156 Right rear turn signal output open
B2158 Right rear turn signal output shorted low
B2159 Right rear turn signal output overloaded
B2161 Brake lamp output open
B2163 Brake lamp output shorted low
B2164 Brake lamp output overloaded
B2168 Running lights output shorted low
B2169 Running lights output overloaded
B2172 H2 output shorted high
B2173 H2 output shorted low
B2176 Security antenna output open
B2177 Security antenna output shorted high
B2178 Security antenna output shorted low
B2183 G2 output shorted low
B2188 G3 output shorted low
B2193 H4 output shorted low
B2198 H3 output shorted low
B2201 IGN switch off w/VSS
B2203 Ignition switch input shorted low
B2206 Run/stop switch input open/shorted high
B2208 Run/stop switch input shorted low
B2210 Run/stop switch inputs both open
B2212 Run/stop switch inputs both closed
B2218 Neutral switch shorted low
B2223 Rear brake switch shorted low (light on)
B2226 BAS input open
B2228 BAS input shorted low
B2231 Fork locked/VSS
B2232 Fork lock shorted high
B2233 Fork lock shorted low
B2234 Fork lock detected with option disabled
B2235 Fork lock configuration invalid
B2250 Clutch switch stuck
B2251 Horn switch stuck
B2253 FTP switch stuck
B2254 Left turn switch stuck
B2255 Trip switch stuck
B2256 LHCM Police siren power stuck
B2257 LHCM Police siren wail power stuck
B2258 LHCM police siren yelp stuck
B2260 Start switch stuck
B2261 Right turn switch stuck
B2262 Front brake switch stuck
B2263 Hazard switch stuck
B2264 RHCM police lights power switch stuck
B2265 RHCM police lights front switch stuck
B2266 RHCM police lights rear switch stuck
B2267 RHCM police ICR switch stuck
B2270 BCM internal error
B2271 BCM voltage low
B2272 BCM/IM voltage high
B2274 Constant battery line error
U0001 CAN BUS error
U0002 CAN comm bus perf error
U0003 Network management monitoring
U0100 Lost comm w/ECM
U0121 Lost comm W/ABS
U0140 Lost comm W/BCM
U0141 Lost comm w/LHCM
U0142 Lost comm w/RHCM
U0156 Lost comm w/SPEEDO
U0158 Lost comm w/fuel gauge
U0159 Lost comm w/volt gauge
U0160 Lost comm w/ fuel and volt gauge
U0184 Lost comm w/radio
U0185 Lost comm w/Amp 1
U0186 Lost comm w/ AMP 2
U1016 Loss of ECM Serial Data
U1064 Loss of TSM/FSFM Serial Data to ECM
U1097 Loss of SpeedometerSerial Data to ECM
U1255 Serial Data Error
U1300 ECM Serial Data Low
U1300 Serial Data Low
U1301 ECM Serial Data High
U1301 Serial Data High
U1302 ACC bus perf error
U1401 Lost com w/CB
The trip odometer trigger switch is located in the left hand control module.
The switch signal is sent to the speedometer over the CAN bus.
If there is a problem with the CAN bus, the odometer self-diagnostic mode maynot function.
For a quick check of instrument function, perform a «WOW» test by entering odometer self-diagnostics.
Background lighting will illuminate, gauge needles will sweep their full range of motion and all indicator lamps
controlled by the CAN circuit will illuminate.
If the instrument fails «WOW» test, check for battery power and ground to the instrument.
If any feature in the speedometer is non-functional, see Description and Operation.
Table 1. Diagnostic Trouble Codes (DTCs) and Fault Conditions
DTC PRIORITYORDER
FAULT CONDITION SOLUTION
B1103 47 LHCM internal error
B1153 46 RHCM internal error
B1200 37 IM internal fault
B1210 176 Fuel level sender shorted low/open
B1211 182 Fuel level sender shorted high
B1212 175 Fuel signal low
B1213 176 Fuel signal high
B1300 340 Radio voltage high
B1301 341 Radio voltage low
B1302 342 Faceplate home button stuck
B1303 343 Faceplate favorite button stuck
B1304 344 Faceplate navigation button stuck
B1305 345 Faceplate power/mute button stuck
B1306 399 Rear hand controls shorted high
B1307 400 Rear hand controls shorted low
B1308 401 Rear volume up button stuck
B1309 402 Rear volume down button stuck
B1310 403 Rear mode button stuck
B1311 404 Rear PTT button stuck
B1312 405 Rear tune up button stuck
Diagnostic Tips
B1313 406 Rear tune down button stuck
B1314 346 LHCM VR PTT button stuck
B1315 347 LHCM up button stuck
B1316 348 LHCM left button stuck
B1317 349 LHCM center button stuck
B1318 350 LHCM right button stuck
B1319 351 LHCM down button stuck
B1320 352 RHCM info button stuck
B1321 353 RHCM up button stuck
B1322 354 RHCM left button stuck
B1323 355 RHCM center button stuck
B1324 356 RHCM right button stuck
B1325 357 RHCM down button stuck
B1326 358 RHCM CB squelch up button stuck
B1327 359 RHCM CB PTT button stuck
B1328 360 RHCM CB squelch down button stuck
B1329 361 Faceplate preset button 1 stuck
B1330 362 Faceplate preset button 2 stuck
B1331 363 Faceplate preset button 3 stuck
B1332 364 Faceplate preset button 4 stuck
B1333 365 Faceplate preset button 5 stuck
B1334 366 Faceplate preset button 6 stuck
B1335 367 Faceplate preset button 7 stuck
B1336 368 Faceplate preset button 8 stuck
B1337 369 Front left speaker shorted together
B1338 370 Front left speaker open
B1339 371 Front left speaker shorted low
B1340 372 Front left speaker shorted high
B1341 373 Rear left speaker shorted together
B1342 374 Rear left speaker open
B1343 375 Rear left speaker shorted low
B1344 376 Rear left speaker shorted high
B1345 377 Front right speaker shorted together
B1346 378 Front right speaker open
B1347 379 Front right speaker shorted low
B1348 380 Front right speaker shorted high
B1349 381 Rear right speaker shorted together
B1350 382 Rear right speaker open
B1351 383 Rear right speaker shorted low
B1352 384 Rear right speaker shorted high
B1353 385 Speaker output DC offset
B1354 386 GPS antenna open
B1355 387 GPS antenna shorted low
B1356 388 SDARS antenna open
B1357 389 SDARS antenna shorted
B1358 390 Front left headset shorted high
B1359 391 Front right headset shorted high
B1360 392 Front left headset shorted low
B1361 393 Front right headset shorted low
B1362 394 Rear left headset shorted high
B1363 395 Rear right headset shorted high
B1364 396 Rear left headset shorted low
B1365 397 Rear right headset shorted low
B1366 398 Internal thermal shutdown error
B1367 451 WIM fault detected Code used to support P&
A parts.
B1401 407 Amp voltage low
B1402 408 Amp voltage high
B1403 409 Speaker output DC offset
B1404 410 Internal thermal shutdown error
B1405 427 EQ correlation error
B1406 428 Invalid or missing EQ
B1410 411 Channel 1 speaker open
B1411 412 Channel 1 speaker shorted low
B1412 413 Channel 1 speaker shorted high
B1413 414 Channel 1 speaker shorted together
B1420 415 Channel 2 speaker open
B1421 416 Channel 2 speaker shorted low
B1422 417 Channel 2 speaker shorted high
B1423 418 Channel 2 speaker shorted together
B1430 419 Channel 3 speaker open
B1431 420 Channel 3 speaker shorted low
B1432 421 Channel 3 speaker shorted high
B1433 422 Channel 3 speaker shorted together
B1440 423 Channel 4 speaker open
B1441 424 Channel 4 speaker shorted low
B1442 425 Channel 4 speaker shorted high
B1443 426 Channel 4 speaker shorted together
B2102 4 System power output shorted high
B2103 5 System power output shorted low
B2104 6 System power output overloaded
B2106 257 L4 output open
B2107 225 L4 output shorted high
B2108 226 L4 output shorted low
B2109 227 L4 output overloaded
B2112 132 ACC output shorted high
B2113 134 ACC output shorted low
B2114 136 ACC output overloaded
B2116 92 Fuel pump output open
B2117 93 Fuel pump output shorted high
B2118 94 Fuel pump output shorted low
B2119 95 Fuel pump output overloaded
B2121 58 Starter output open
B2122 59 Starter output shorted high
B2123 60 Starter output shorted low
B2124 61 Starter output overloaded
B2127 243 E4 output shorted high
B2128 244 E4 output shorted low
B2129 245 E4 output overloaded
B2131 233 High beam output open
B2132 234 High beam output shorted high
B2133 235 High beam output shorted low
B2134 236 High beam output overloaded
B2136 229 Low beam output open
B2137 230 Low beam output shorted high
B2138 231 Low beam output shorted low
B2139 232 Low beam output overloaded
B2141 207 Left front turn signal output open
B2143 214 Left front turn signal output shorted low
B2144 215 Left front turn signal output overloaded
B2146 216 Right front turn signal output open
B2148 217 Right front turn signal output shorted low
B2149 218 Right front turn signal output overloaded
B2151 219 Left rear turn signal output open
B2153 220 Left rear turn signal output shorted low
B2154 221 Left rear turn signal output overloaded
B2156 222 Right rear turn signal output open
B2158 223 Right rear turn signal output shorted low
B2159 224 Right rear turn signal output overloaded
B2161 198 Brake lamp output open
B2163 199 Brake lamp output shorted low
B2164 200 Brake lamp output overloaded
B2168 172 Running lights output shorted low
B2169 173 Running lights output overloaded
B2172 237 H2 output shorted high
B2173 238 H2 output shorted low
B2176 239 Security antenna output open
B2177 240 Security antenna output shorted high
B2178 241 Security antenna output shorted low
B2183 249 G2 output shorted low
B2188 254 G3 output shorted low
B2193 257 H4 output shorted low
B2198 259 H3 output shorted low
B2201 52 IGN switch off w/VSS
B2202 53 Ignition switch accy with vehicle speed
B2203 50 Ignition switch input shorted low
B2206 51 Run/stop switch input open/shorted high
B2208 54 Run/stop switch input shorted low
B2210 55 Run/stop switch inputs both open
B2212 56 Run/stop switch inputs both closed
B2218 131 Neutral switch shorted low
B2223 197 Rear brake switch shorted low (light on)
B2226 247 BAS input open BCM not configured properly.
B2228 250 BAS input shorted low BCM not configured properly.
B2231 312 Fork locked w/VSS BCM not configured properly. This DTC should
only apply to CVO models.
B2232 313 Fork lock shorted high BCM not configured properly. This DTC should
only apply to CVO models.
B2233 314 Fork lock shorted low BCM not configured properly. This DTC should
only apply to CVO models.
B2234 315 Fork lock detected w/option disabled
BCM not configured properly. This DTC should
only apply to CVO models.
B2235 316 Fork lock configuration invalid BCM not configured properly. This DTC should
only apply to CVO models.
B2250 128 Clutch switch stuck
B2251 242 Horn switch stuck
B2253 228 FTP switch stuck
B2254 203 Left turn switch stuck
B2255 246 Trip switch stuck
B2256 208 LHCM police siren power switch stuck
BCM not configured properly. This DTC should
only apply to Police models.
B2257 209 LHCM police siren wail power switch stuck
BCM not configured properly. This DTC should
only apply to Police models.
B2258 210 LHCM police siren yelp switch stuck BCM not configured properly. This DTC should
only apply to Police models.
B2260 57 Start switch stuck
B2261 204 Right turn switch stuck
B2262 196 Front brake switch stuck
B2263 202 Hazard switch stuck
B2264 211 RHCM police lights power switch BCM not configured properly. This DTC should stuck only apply to Police models.
B2265 212 RHCM police lights front switch stuck
BCM not configured properly. This DTC should
only apply to Police models.
B2266 213 RHCM police lights rear switch stuck
BCM not configured properly. This DTC should
only apply to Police models.
B2270 27 BCM internal error
B2271 26 BCM voltage low
B2272 33 BCM/IM voltage high
B2274 49 Constant battery line error
C0562 38 ABS voltage low
C0563 40 ABS voltage high
C1014 183 ABS ECU relay error
C1021 191 ABS front WSS always zero
C1023 192 ABS rear WSS always zero
C1025 194 ABS front wheel speed intermittent
C1027 195 ABS rear wheel speed intermittent
C1029 193 ABS wheel speed difference too high
C1032 189 ABS front wheel speed circuit open/shorted
C1034 190 ABS rear wheel speed circuit open/shorted
C1040 184 ABS pump/motor error
C1055 39 ABS ECU internal error
C1061 185 ABS front apply solenoid circuit open/high resistance
C1062 187 ABS front release solenoid circuit open/high resistance
C1065 186 ABS rear apply solenoid circuit open/high resistance
C1066 188 ABS rear release solenoid circuit open/high resistance
C1071 283 Rear prime valve error
C1072 284 Rear isolation valve error
C1073 285 Front isolation valve error
C1074 286 Front prime valve error
C1075 287 Front linked inlet valve error
C1076 288 Front linked outlet valve error
C1077 289 Front circuit pressure sensor error
C1078 290 Rear circuit pressure sensor error
C1081 291 Front master pressure sensor error
C1082 292 Front master pressure sensor offset error
C1083 293 Front wheel pressure sensor error
C1084 294 Front wheel pressure sensor offset error
C1085 295 Rear master pressure sensor error
C1086 296 Rear master pressure sensor offset error
C1087 297 Rear wheel pressure sensor error
C1088 298 Rear wheel pressure sensor offset error
C1089 299 Pressure sensor external supply error
C1159 43 ABS invalid stored VIN
C1178 41 ABS no VIN received from ECM
C1184 42 ABS invalid VIN from ECM
C1195 266 Wake up error
P0031 153 Front HO2S low/open
P0032 156 Front HO2S shorted high
P0051 154 Rear HO2S low/open
P0052 155 Rear HO2S shorted high
P0072 112 AAT sensor low
P0073 113 AAT sensor high/open
P0107 100 MAP sensor failed low/open
P0108 101 MAP sensor failed high/open port
P0112 123 IAT sensor shorted low
P0113 125 IAT sensor high/open
P0117 102 ET sensor shorted low
P0118 107 ET sensor high/open
P0120 76 TPS 1 range error
P0122 74 TPS 1 low
P0123 75 TPS 1 high/open
P0131 157 O2 sensor low/engine lean (front)
P0132 159 Engine running rich (front)
P0134 161 Oxygen sensor high/open (front)
P0151 158 O2 sensor low/engine lean (rear)
P0152 160 Engine running rich (rear)
P0154 162 O2 sensor high/open (rear)
P0220 79 TPS 2 range error
P0222 77 TPS 2 low/open
P0223 78 TPS 2 high
P0261 96 Fuel injector low/open (front)
P0262 97 Fuel injector shorted high (front)
P0264 98 Fuel injector low/open (rear)
P0265 99 Fuel injector shorted high (rear)
P0325 139 Knock sensor front open circuit
P0327 140 Knock sensor front circuit low
P0328 141 Knock sensor front circuit high
P0330 142 Knock sensor rear open circuit
P0332 143 Knock sensor rear circuit low
P0333 144 Knock sensor rear circuit high
P0371 65 CKP sensor wrong number of Description and Operation pulses
P0374 64 CKP sensor no pulses
P0444 147 Purge solenoid low/open
P0445 148 Purge solenoid shorted high
P0462 174 Fuel sender shorted low
P0463 175 Fuel sender shorted high/open
P0502 137 VSS failed low
P0503 138 VSS failed high
P0505 148 Idle speed control — unstable Loss of Idle Speed Control
P0522 168 Engine oil pressure sensor/switchм shorted low
P0523 169 Engine oil pressure sensor/switch shorted high/open
P0562 127 ECM voltage low
P0572 202 Brake switch low
P0577 163 Cruise control input error
P0603 29 ECM EEPROM memory error
P0605 28 ECM FLASH memory error
P0641 62 5 Volt reference out of range
P0651 63 5 Volt reference 2 out of range
P0693 119 Chassis fan control circuit shorted low
P0694 120 Chassis fan control circuit shorted high
P1009 32 VTD disabled fuel due to bad password
General
P1017 103 ET indicates overheating
P1019 106 ECT difference (high temp)
P1270 67 TGS 2 A/D validation error
P1501 166 JSS low
P1502 167 JSS high/open
P1505 445 Power limit violation
P1510 447 ETC limited performance mode
P1511 448 ETC power management mode
P1512 449 ETC forced idle mode
P1514 87 ETC airflow error
P1600 66 ETC watchdog error
P1655 164 ACR solenoid low/open
P1656 165 ACR solenoid shorted high
P1691 115 Cooling fan left low/open
P1692 116 Cooling fan left shorted high
P1693 117 Cooling fan right low/open
P1694 118 Cooling fan right shorted high
P2100 82 ETC driver open circuit
P2101 83 ETC actuation error
P2102 84 ETC driver shorted low
P2103 85 ETC driver shorted high
P2105 446 ETC forced shutdown mode
P2107 68 ETC driver internal error
P2119 81 ETC actuator return error
P2122 69 TGS 1 low/open
P2123 70 TGS 1 high
P2127 71 TGS 2 low/open
P2128 72 TGS 2 high
P2135 80 TPS correlation error
P2138 73 TGS correlation error
P2176 86 ETC zero position learning error
P2184 121 ECT sensor low
P2185 122 ECT sensor high
P2300 88 Ignition coil driver low/open (front)
P2301 89 Ignition coil driver shorted high (front)
P2303 90 Ignition coil driver low/open (rear)
P2304 91 Ignition coil driver shorted high (rear)
P2602 104 Coolant pump «A» control circuit low
P2603 105 Coolant pump «A» control circuit high
U0001 1 CAN BUS error
U0002 16 CAN comm bus perf error
U0003 13 Network management monitoring
U0011 2 CAN bus low shorted to CAN bus high
U0100 7 Lost comm w/ECM
U0121 11 Lost comm w/ABS
U0140 3 Lost comm w/BCM
U0141 9 Lost comm w/LHCM
U0142 8 Lost comm w/RHCM
U0156 10 Lost comm w/speedo
U0158 180 Lost comm w/fuel gauge
U0159 181 Lost comm w/volt gauge
U0160 179 Lost comm w/fuel and volt gauges
U0184 323 Lost comm w/radio
U0185 325 Lost comm w/AMP 1
U0186 326 Lost comm w/AMP 2
U0300 15 Internal control module software incompatibility
U1302 324 ACC bus perf error
U1401 331 Lost comm w/CB
U1401 331 Lost comm w/CB
U1405 450 ACC bus lost comm w/ WIM Code used to support P&A parts
The trip odometer trigger switch is located in the left hand control module.
The switch signal is sent to the speedometer over the CAN bus.
If there is a problem with the CAN bus, the odometer self-diagnostic mode maynot function.
For a quick check of instrument function, perform a «WOW» test by entering odometer self-diagnostics.
Background lighting will illuminate, gauge needles will sweep their full range of motion and all indicator lamps
controlled by the CAN circuit will illuminate.
If the instrument fails «WOW» test, check for battery power and ground to the instrument.
If any feature in the speedometer is non-functional, see Description and Operation.
Table 1. Diagnostic Trouble Codes (DTCs) and Fault Conditions
DTC PRIORITYORDER
FAULT CONDITION SOLUTION
B1103 47 LHCM internal error
B1153 46 RHCM internal error
B1200 37 IM internal fault
B1210 176 Fuel level sender shorted low/open
B1211 182 Fuel level sender shorted high
B1212 175 Fuel signal low
B1213 176 Fuel signal high
B1300 340 Radio voltage high
B1301 341 Radio voltage low
B1302 342 Faceplate home button stuck
B1303 343 Faceplate favorite button stuck
B1304 344 Faceplate navigation button stuck
B1305 345 Faceplate power/mute button stuck
B1306 399 Rear hand controls shorted high
B1307 400 Rear hand controls shorted low
B1308 401 Rear volume up button stuck
B1309 402 Rear volume down button stuck
B1310 403 Rear mode button stuck
B1311 404 Rear PTT button stuck
B1312 405 Rear tune up button stuck
Diagnostic Tips
B1313 406 Rear tune down button stuck
B1314 346 LHCM VR PTT button stuck
B1315 347 LHCM up button stuck
B1316 348 LHCM left button stuck
B1317 349 LHCM center button stuck
B1318 350 LHCM right button stuck
B1319 351 LHCM down button stuck
B1320 352 RHCM info button stuck
B1321 353 RHCM up button stuck
B1322 354 RHCM left button stuck
B1323 355 RHCM center button stuck
B1324 356 RHCM right button stuck
B1325 357 RHCM down button stuck
B1326 358 RHCM CB squelch up button stuck
B1327 359 RHCM CB PTT button stuck
B1328 360 RHCM CB squelch down button stuck
B1329 361 Faceplate preset button 1 stuck
B1330 362 Faceplate preset button 2 stuck
B1331 363 Faceplate preset button 3 stuck
B1332 364 Faceplate preset button 4 stuck
B1333 365 Faceplate preset button 5 stuck
B1334 366 Faceplate preset button 6 stuck
B1335 367 Faceplate preset button 7 stuck
B1336 368 Faceplate preset button 8 stuck
B1337 369 Front left speaker shorted together
B1338 370 Front left speaker open
B1339 371 Front left speaker shorted low
B1340 372 Front left speaker shorted high
B1341 373 Rear left speaker shorted together
B1342 374 Rear left speaker open
B1343 375 Rear left speaker shorted low
B1344 376 Rear left speaker shorted high
B1345 377 Front right speaker shorted together
B1346 378 Front right speaker open
B1347 379 Front right speaker shorted low
B1348 380 Front right speaker shorted high
B1349 381 Rear right speaker shorted together
B1350 382 Rear right speaker open
B1351 383 Rear right speaker shorted low
B1352 384 Rear right speaker shorted high
B1353 385 Speaker output DC offset
B1354 386 GPS antenna open
B1355 387 GPS antenna shorted low
B1356 388 SDARS antenna open
B1357 389 SDARS antenna shorted
B1358 390 Front left headset shorted high
B1359 391 Front right headset shorted high
B1360 392 Front left headset shorted low
B1361 393 Front right headset shorted low
B1362 394 Rear left headset shorted high
B1363 395 Rear right headset shorted high
B1364 396 Rear left headset shorted low
B1365 397 Rear right headset shorted low
B1366 398 Internal thermal shutdown error
B1367 451 WIM fault detected Code used to support P&
A parts.
B1401 407 Amp voltage low
B1402 408 Amp voltage high
B1403 409 Speaker output DC offset
B1404 410 Internal thermal shutdown error
B1405 427 EQ correlation error
B1406 428 Invalid or missing EQ
B1410 411 Channel 1 speaker open
B1411 412 Channel 1 speaker shorted low
B1412 413 Channel 1 speaker shorted high
B1413 414 Channel 1 speaker shorted together
B1420 415 Channel 2 speaker open
B1421 416 Channel 2 speaker shorted low
B1422 417 Channel 2 speaker shorted high
B1423 418 Channel 2 speaker shorted together
B1430 419 Channel 3 speaker open
B1431 420 Channel 3 speaker shorted low
B1432 421 Channel 3 speaker shorted high
B1433 422 Channel 3 speaker shorted together
B1440 423 Channel 4 speaker open
B1441 424 Channel 4 speaker shorted low
B1442 425 Channel 4 speaker shorted high
B1443 426 Channel 4 speaker shorted together
B2102 4 System power output shorted high
B2103 5 System power output shorted low
B2104 6 System power output overloaded
B2106 257 L4 output open
B2107 225 L4 output shorted high
B2108 226 L4 output shorted low
B2109 227 L4 output overloaded
B2112 132 ACC output shorted high
B2113 134 ACC output shorted low
B2114 136 ACC output overloaded
B2116 92 Fuel pump output open
B2117 93 Fuel pump output shorted high
B2118 94 Fuel pump output shorted low
B2119 95 Fuel pump output overloaded
B2121 58 Starter output open
B2122 59 Starter output shorted high
B2123 60 Starter output shorted low
B2124 61 Starter output overloaded
B2127 243 E4 output shorted high
B2128 244 E4 output shorted low
B2129 245 E4 output overloaded
B2131 233 High beam output open
B2132 234 High beam output shorted high
B2133 235 High beam output shorted low
B2134 236 High beam output overloaded
B2136 229 Low beam output open
B2137 230 Low beam output shorted high
B2138 231 Low beam output shorted low
B2139 232 Low beam output overloaded
B2141 207 Left front turn signal output open
B2143 214 Left front turn signal output shorted low
B2144 215 Left front turn signal output overloaded
B2146 216 Right front turn signal output open
B2148 217 Right front turn signal output shorted low
B2149 218 Right front turn signal output overloaded
B2151 219 Left rear turn signal output open
B2153 220 Left rear turn signal output shorted low
B2154 221 Left rear turn signal output overloaded
B2156 222 Right rear turn signal output open
B2158 223 Right rear turn signal output shorted low
B2159 224 Right rear turn signal output overloaded
B2161 198 Brake lamp output open
B2163 199 Brake lamp output shorted low
B2164 200 Brake lamp output overloaded
B2168 172 Running lights output shorted low
B2169 173 Running lights output overloaded
B2172 237 H2 output shorted high
B2173 238 H2 output shorted low
B2176 239 Security antenna output open
B2177 240 Security antenna output shorted high
B2178 241 Security antenna output shorted low
B2183 249 G2 output shorted low
B2188 254 G3 output shorted low
B2193 257 H4 output shorted low
B2198 259 H3 output shorted low
B2201 52 IGN switch off w/VSS
B2202 53 Ignition switch accy with vehicle speed
B2203 50 Ignition switch input shorted low
B2206 51 Run/stop switch input open/shorted high
B2208 54 Run/stop switch input shorted low
B2210 55 Run/stop switch inputs both open
B2212 56 Run/stop switch inputs both closed
B2218 131 Neutral switch shorted low
B2223 197 Rear brake switch shorted low (light on)
B2226 247 BAS input open BCM not configured properly.
B2228 250 BAS input shorted low BCM not configured properly.
B2231 312 Fork locked w/VSS BCM not configured properly. This DTC should
only apply to CVO models.
B2232 313 Fork lock shorted high BCM not configured properly. This DTC should
only apply to CVO models.
B2233 314 Fork lock shorted low BCM not configured properly. This DTC should
only apply to CVO models.
B2234 315 Fork lock detected w/option disabled
BCM not configured properly. This DTC should
only apply to CVO models.
B2235 316 Fork lock configuration invalid BCM not configured properly. This DTC should
only apply to CVO models.
B2250 128 Clutch switch stuck
B2251 242 Horn switch stuck
B2253 228 FTP switch stuck
B2254 203 Left turn switch stuck
B2255 246 Trip switch stuck
B2256 208 LHCM police siren power switch stuck
BCM not configured properly. This DTC should
only apply to Police models.
B2257 209 LHCM police siren wail power switch stuck
BCM not configured properly. This DTC should
only apply to Police models.
B2258 210 LHCM police siren yelp switch stuck BCM not configured properly. This DTC should
only apply to Police models.
B2260 57 Start switch stuck
B2261 204 Right turn switch stuck
B2262 196 Front brake switch stuck
B2263 202 Hazard switch stuck
B2264 211 RHCM police lights power switch BCM not configured properly. This DTC should stuck only apply to Police models.
B2265 212 RHCM police lights front switch stuck
BCM not configured properly. This DTC should
only apply to Police models.
B2266 213 RHCM police lights rear switch stuck
BCM not configured properly. This DTC should
only apply to Police models.
B2270 27 BCM internal error
B2271 26 BCM voltage low
B2272 33 BCM/IM voltage high
B2274 49 Constant battery line error
C0562 38 ABS voltage low
C0563 40 ABS voltage high
C1014 183 ABS ECU relay error
C1021 191 ABS front WSS always zero
C1023 192 ABS rear WSS always zero
C1025 194 ABS front wheel speed intermittent
C1027 195 ABS rear wheel speed intermittent
C1029 193 ABS wheel speed difference too high
C1032 189 ABS front wheel speed circuit open/shorted
C1034 190 ABS rear wheel speed circuit open/shorted
C1040 184 ABS pump/motor error
C1055 39 ABS ECU internal error
C1061 185 ABS front apply solenoid circuit open/high resistance
C1062 187 ABS front release solenoid circuit open/high resistance
C1065 186 ABS rear apply solenoid circuit open/high resistance
C1066 188 ABS rear release solenoid circuit open/high resistance
C1071 283 Rear prime valve error
C1072 284 Rear isolation valve error
C1073 285 Front isolation valve error
C1074 286 Front prime valve error
C1075 287 Front linked inlet valve error
C1076 288 Front linked outlet valve error
C1077 289 Front circuit pressure sensor error
C1078 290 Rear circuit pressure sensor error
C1081 291 Front master pressure sensor error
C1082 292 Front master pressure sensor offset error
C1083 293 Front wheel pressure sensor error
C1084 294 Front wheel pressure sensor offset error
C1085 295 Rear master pressure sensor error
C1086 296 Rear master pressure sensor offset error
C1087 297 Rear wheel pressure sensor error
C1088 298 Rear wheel pressure sensor offset error
C1089 299 Pressure sensor external supply error
C1159 43 ABS invalid stored VIN
C1178 41 ABS no VIN received from ECM
C1184 42 ABS invalid VIN from ECM
C1195 266 Wake up error
P0031 153 Front HO2S low/open
P0032 156 Front HO2S shorted high
P0051 154 Rear HO2S low/open
P0052 155 Rear HO2S shorted high
P0072 112 AAT sensor low
P0073 113 AAT sensor high/open
P0107 100 MAP sensor failed low/open
P0108 101 MAP sensor failed high/open port
P0112 123 IAT sensor shorted low
P0113 125 IAT sensor high/open
P0117 102 ET sensor shorted low
P0118 107 ET sensor high/open
P0120 76 TPS 1 range error
P0122 74 TPS 1 low
P0123 75 TPS 1 high/open
P0131 157 O2 sensor low/engine lean (front)
P0132 159 Engine running rich (front)
P0134 161 Oxygen sensor high/open (front)
P0151 158 O2 sensor low/engine lean (rear)
P0152 160 Engine running rich (rear)
P0154 162 O2 sensor high/open (rear)
P0220 79 TPS 2 range error
P0222 77 TPS 2 low/open
P0223 78 TPS 2 high
P0261 96 Fuel injector low/open (front)
P0262 97 Fuel injector shorted high (front)
P0264 98 Fuel injector low/open (rear)
P0265 99 Fuel injector shorted high (rear)
P0325 139 Knock sensor front open circuit
P0327 140 Knock sensor front circuit low
P0328 141 Knock sensor front circuit high
P0330 142 Knock sensor rear open circuit
P0332 143 Knock sensor rear circuit low
P0333 144 Knock sensor rear circuit high
P0371 65 CKP sensor wrong number of Description and Operation pulses
P0374 64 CKP sensor no pulses
P0444 147 Purge solenoid low/open
P0445 148 Purge solenoid shorted high
P0462 174 Fuel sender shorted low
P0463 175 Fuel sender shorted high/open
P0502 137 VSS failed low
P0503 138 VSS failed high
P0505 148 Idle speed control — unstable Loss of Idle Speed Control
P0522 168 Engine oil pressure sensor/switchм shorted low
P0523 169 Engine oil pressure sensor/switch shorted high/open
P0562 127 ECM voltage low
P0572 202 Brake switch low
P0577 163 Cruise control input error
P0603 29 ECM EEPROM memory error
P0605 28 ECM FLASH memory error
P0641 62 5 Volt reference out of range
P0651 63 5 Volt reference 2 out of range
P0693 119 Chassis fan control circuit shorted low
P0694 120 Chassis fan control circuit shorted high
P1009 32 VTD disabled fuel due to bad password
General
P1017 103 ET indicates overheating
P1019 106 ECT difference (high temp)
P1270 67 TGS 2 A/D validation error
P1501 166 JSS low
P1502 167 JSS high/open
P1505 445 Power limit violation
P1510 447 ETC limited performance mode
P1511 448 ETC power management mode
P1512 449 ETC forced idle mode
P1514 87 ETC airflow error
P1600 66 ETC watchdog error
P1655 164 ACR solenoid low/open
P1656 165 ACR solenoid shorted high
P1691 115 Cooling fan left low/open
P1692 116 Cooling fan left shorted high
P1693 117 Cooling fan right low/open
P1694 118 Cooling fan right shorted high
P2100 82 ETC driver open circuit
P2101 83 ETC actuation error
P2102 84 ETC driver shorted low
P2103 85 ETC driver shorted high
P2105 446 ETC forced shutdown mode
P2107 68 ETC driver internal error
P2119 81 ETC actuator return error
P2122 69 TGS 1 low/open
P2123 70 TGS 1 high
P2127 71 TGS 2 low/open
P2128 72 TGS 2 high
P2135 80 TPS correlation error
P2138 73 TGS correlation error
P2176 86 ETC zero position learning error
P2184 121 ECT sensor low
P2185 122 ECT sensor high
P2300 88 Ignition coil driver low/open (front)
P2301 89 Ignition coil driver shorted high (front)
P2303 90 Ignition coil driver low/open (rear)
P2304 91 Ignition coil driver shorted high (rear)
P2602 104 Coolant pump «A» control circuit low
P2603 105 Coolant pump «A» control circuit high
U0001 1 CAN BUS error
U0002 16 CAN comm bus perf error
U0003 13 Network management monitoring
U0011 2 CAN bus low shorted to CAN bus high
U0100 7 Lost comm w/ECM
U0121 11 Lost comm w/ABS
U0140 3 Lost comm w/BCM
U0141 9 Lost comm w/LHCM
U0142 8 Lost comm w/RHCM
U0156 10 Lost comm w/speedo
U0158 180 Lost comm w/fuel gauge
U0159 181 Lost comm w/volt gauge
U0160 179 Lost comm w/fuel and volt gauges
U0184 323 Lost comm w/radio
U0185 325 Lost comm w/AMP 1
U0186 326 Lost comm w/AMP 2
U0300 15 Internal control module software incompatibility
U1302 324 ACC bus perf error
U1401 331 Lost comm w/CB
U1401 331 Lost comm w/CB
U1405 450 ACC bus lost comm w/ WIM Code used to support P&A parts
The Twin Cam allows us to see the Harley error codes also known as the diagnostic trouble codes.
This videos reviews how to retrieve the codes and this process will help you determine where to look and test. Don’t just go out and by a new sensor or part. Find out what’s going on.
More Video Tech Tips Here.
Here are some of the various diagnostic trouble code lists (DTCs) used on ICM/ECM equipped HD models through 2008:
HFSM = Hands Free Security Module
TSSM = Turn Signal Security Module
TSM = Turn signal module
B0563 Battery Voltage High TSM/TSSM
B1004 Fuel Level Sending Unit Low Instruments
B1005 Fuel Level Sending Unit High/Open Instruments
B1006 Accessory Line Overvoltage Instruments
B1007 Ignition Line Overvoltage Instruments
B1008 Reset Switch Closed Instruments
B1121 (TSM) Left Turn Output Fault – (HFSM) Left Turn Output Open
B1122 (TSM) Right Turn Output Fault – (HFSM) Right Turn Output Open
B1123 (HFSM) Left Turn Output Short to Ground
B1124 (HFSM) Right Turn Output Short to Ground
B1125 (HFSM) Left Turn Output Short to Battery
B1126 (HFSM) Right Turn Output Short to Battery
B1131 (HFSM) Alarm Output Low
B1131 Alarm Output Low TSM/TSSM
B1132 (HFSM) Alarm Output High
B1132 Alarm Output High TSM/TSSM
B1134 Starter Output High TSM/TSSM
B1135 Accelerometer Fault TSM/TSSM
B1136 (HFSM) Accelerometer Tip Test Error
B1141 (TSM) Ignition Switch Low/Open – (HFSM) Ignition Switch Low/Open
B1142 Smart Security System Internal Fault
B1143 (HFSM) Security Antenna Short to Ground
B1144 (HFSM) Security Antenna Short to Battery
B1145 (HFSM) Security Antenna Open
B1151 Bank Angle Sensor(BAS) Short to Ground
B1151 Sidecar BAS Low TSM/TSSM
B1152 Bank Angle Sensor(BAS) Short to Battery
B1152 Sidecar BAS High TSM/TSSM
B1153 Bank Angle Sensor(BAS) High
B1153 Sidecar BAS Out of Range TSM/TSSM
B1154 Clutch Switch Input Short to Ground
B1155 Neutral Switch Input Short to Battery
P0106 MAP Sensor Rate of Range Error Carb
P0107 Map Sensor Failed Open/Low Carb
P0107 Map Sensor Open/Low EFI
P0108 Map Sensor Failed High Carb
P0108 Map Sensor High
P0112I AT Voltage Low
P0113I AT Sensor Voltage Open/High EFI
P0113I AT Voltage Open/High
P0117 ET Sensor Low
P0118 ET Sensor High
P0118 ET Sensor Voltage Open/High EFI
P0120 TPS1 Range Error
P0122 TP Sensor Open/Low EFI
P0122 TPS1 Low
P0123 TP Sensor High EFI
P0123 TPS2 High/Open
P0131 Front Oxygen Sensor Low
P0132 Front Oxygen Sensor High
P0134 Front Oxygen Sensor Inactive
P0151 Rear Oxygen Sensor Low
P0152 Rear Oxygen Sensor High
P0154 Rear Oxygen Sensor Inactive
P0220 TPS2 Range Error
P0222 TPS2 Low
P0223 TPS2 High/Open
P0261 Front Injector Open/Low
P0262 Front Injector High EFI
P0263 Rear Injector Open/Low EFI
P0264 Rear Injector High EFI
P0371 Crank Position Sensor (CKP)
P0372 Crank Position Sensor (CKP)
P0373 CKP Sensor Intermittent
P0374 CKP Sensor Not Detected Carb
P0374 CKP Sensor Synch Error EFI
P0444 Purge Solenoid Open/Low
P0445 Purge Solenoid High
P0501 VSS Sensor Low
P0502 VSS High/Open
P0505 Loss of Idle Sped Control EFI
P0562 Battery Voltage Low
P0563 Battery Voltage High
P0572 Brake Switch Low
P0577 Cruise Control Input High
P0602 Calibration Memory Error Carb
P0603 ECM EEPROM Memory Error
P0603 EEPROM Failure Carb
P0604 RAM Failure Carb
P0605 ECM Flash Error EFI
P0605 ECM FLASH Memory Error
P0605 Program Memory Error Carb
P0607 Converter Error Carb
P06415 V+Vref 1 Out Of Range
P06515 V+Vref 2 Out Of Range
P1001 System Relay Coil Open/Low
P1002 System Relay Coil High/Shorted
P1003 System relay contacts open
P1004 System Relay Contacts Closed
P1009 Incorrect Password
P1010 Missing Password
P1270 TGS Validation Error
P1351 Front Ignition Coil Driver Open/Low
P1352 Front Ignition Coil Driver High/Shorted
P1353 Front Cylinder No Combustion
P1354 Rear Ignition Coil Driver Open/Low
P1355 Rear Ignition Coil Driver High/Shorted
P1356 Rear Cylinder No Combustion
P1357 Front Cylinder Combustion Intermittent
P1358 Rear Cylinder Combustion Intermittent
P1475 Exhaust Actuation Position Error
P1477 Exhaust Actuator Open/Low
P1478 Exhaust Actuator Shorted/High
P1501 Jiffy Stand Sensor Low
P1502 Jiffy Stand Sensor High
P1510 EFI Limited Performance Mode
P1511 EFI Power Management Mode
P1512 EFI Forced Idle Mode
P1514 Air Flow Fault
P1600 EFI Module Processor Internal Error
P2100 EFI Motor Circuit Open
P2101 EFI Motor Circuit Range Performance (Actuation Error)
P2102 EFI Motor Circuit Low
P2103 EFI Motor Circuit High
P2105 EFI Forced engine shutdown
P2107 EFI Module Processor Internal Fault
P2119 EFI Motor Throttle Body Range Performance
P2122 TGS1 Low/Open
P2123 TGS1 High
P2127 TGS2 Low/Open
P2128 TGS2 High
P2135 TPS Correlation Error
P2138 TGS Correlation Error (Twist grip sensor)
P2176 EFI Closed Position Not Learned
U1016 Loss of ECM Vehicle Speed, Vehicle Inhibit Motion or Powertrain Security Status TSM/TSSM
U1016 Loss of ICM/ECM Serial Data Instruments
U1064 Loss of TSM/FSFM Serial Data to ICM / ECM
U1064 Loss of TSM/TSSM Serial Data Instruments
U1097 Loss of Speedometer Serial data Carb
U1097 Loss of Speedometer Serial data EFI
U1097 Loss of Speedometer Serial Data to ECM
U1097 Loss of Speedometer Serial data TSM/TSSM
U1255 Missing Message at Speedometer EFI
U1255 Serial Data Error
U1255 Serial Data Error/Missing Message EFI
U1255 Serial Data Error/Missing Message Instruments
U1255 Serial Data Error/Missing Message TSM/TSSM
U1300 ECM Serial Data Low
U1300 Serial Data Low
U1300 Serial Data Low Instruments
U1300 Serial Data Low TSM/TSSM
U1301 Serial Data Open/High Carb
U1301 Serial Data Open/High EFI
U1301 Serial Data Open/High Instruments
U1301 Serial Data Open/High TSM/TSSM
AFR – Air Fuel Ratio
ATS – Air Temperature Sensor
BAS – Bank Angle Sensor
CCM – Cruise Control Module
CKP – Crank Position Sensor. The CKP generates an “AC signal” which is sent to the ECM where it is used to reference engine position (TDC) and speed.
DTC – Diagnostic Trouble Codes
ECM – Electronic Control Module. (The Computer) Computes the spark advance for proper ignition timing and fuel control based on sensor inputs (from CKP, MAP & TP sensors) and controls the low-voltage circuits for the ignition coils and injectors. The dwell time for the ignition coil is also calculated in the microprocessor and is dependent upon battery voltage. The programmed dwell feature gives adequate spark at all speeds.
ECT – Engine Coolant Temperature. Sensor also controls the cooling fan relay that provides 12 Vdc to the fans.
EFI – Electronic Fuel Injection
EFP – Electronic Fuel Pump
ET – Engine Temperature sensor
FI – Fuel Injectors
FPR – Fuel Pressure regulator
IAC – Idle Air Control actuator
IAT – Intake Air Temperature sensor
ISS – Ion Sensing System…detonation detection
MAP – manifold Absolute Pressure sensor. The MAP sensor monitors the intake manifold pressure (vacuum) and sends the information to the ECM. The EMC then adjusts the spark and fuel-timing advance curves for optimum performance.
TGS – Twist grip sensor
TPS – Throttle Position Sensor
TSM/TSSM (Turn Signal/ Turn Signal Security Module)
VE – Volume Efficiency
VSS – Vehicle Speed Sensor. Used as an input for idle speed control
Error Codes on 2004-07 Harley Davidson Motorcycles
These will also work on the 07 & 08 bikes. There are additional Harley error codes for the 08 bikes not listed here but are listed in this same section in another post.
These apply to 04 and later bikes with the serial bus. The IM (instrument module) is capable of displaying DTC’s (diagnostic trouble codes).
Speedometer Self Diagnostics: The speedometer is capable of displaying and clearing speedometer, tachometer, TSM/TSSM and ICM/ECM Diagnostic Trouble Codes (DTC).
Turn Ignition switch to OFF & Run/Stop switch is to Run.
Push odometer reset button in & hold.
Turn ignition switch to Ignition and release the odometer reset button. Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine, and cruise) should illuminate. The word “diag” should then appear.
Push the odometer reset button once and you will see the selection menu “PSSPt” with the first P flashing.
Each letter represents an area of the diagnostics module. The module that is flashing is the one you are going to check. To move from one letter (module) to the next, you push the odometer reset button one time. (from P to S to SP to t and back to P, etc.)
- P = ECM/ICM (Electronic Control Module [EFI] / Ignition Control Module [Carbureted)
- S = TSM/TSSM (Turn Signal/ Turn Signal Security Module)
- SP = speedometer
- T = tachometer
To get the DTC within an area of diagnostics, push and hold the odometer reset button in for 5 seconds and release. If there are any DTCs the code will be displayed or the word “none” will appear if there are no DTCs. Push the odometer reset button again to view additional codes if they exist. Record the codes. If DTCs are not to be cleared, Press and release the odometer reset button. Part number of module will be displayed.
NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until ‘clear’ comes up. Release the odometer reset button. Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTCs again by repeating steps 1 to 9. If the code is current it will reappear.
Press and release the odometer reset button to continue to the next module.
Turn Ignition switch to OFF.
On models not equipped with a tachometer “No Rsp” will appear when the tachometer identifier is selected.
“No Rsp” will also appear if the run/off switch is in the off position when doing this procedure.
Also if the code set is a historic code (not a constant light) after 50 start and run cycles of at least 30 seconds each in duration, the light will extinguish itself as long as the error hasn’t occurred again.
If it were a current code, the light would remain lit while running.
DTC FAULT CONDITION MODULE
“BUS Er” Serial data bus shorted/low/open/high
B0563 Battery Voltage High TSM/TSSM
B1004 Fuel Level Sending Unit Low Instruments
B1005 Fuel Level Sending Unit High/Open Instruments
B1006 Accessory Line Over voltage Instruments
B1007 Ignition Line Over voltage Instruments
B1008 Reset Switch Closed Instruments
B1122 Right turn output fault
B1125 (HFSM) Left Turn Output Short to Battery
B1131 Alarm Output Low TSM/TSSM
B1132 Alarm Output High TSM/TSSM
B1134 Starter Output High TSM/TSSM
B1135 Accelerometer Fault TSM/TSSM
B1141 Ignition switch open/low
B1151 Sidecar BAS Low TSM/TSSM
B1152 Sidecar BAS High TSM/TSSM
B1153 Sidecar BAS Out of Range TSM/TSSM
P0106 MAP Sensor Rate of Range Error Carb
P0107 Map Sensor Failed Open/Low Carb
P0107 Map Sensor Open/Low EFI
P0108 Map Sensor Failed High Carb
P0108 Map Sensor High EFI
P0112 IAT Sensor Voltage Low EFI
P0113 IAT Sensor Voltage Open/High EFI
P0117 ET Sensor Voltage Low EFI
P0118 ET Sensor Voltage Open/High EFI
P0122 TP Sensor Open/Low EFI
P0123 TP Sensor High EFI
P0131 Front 02 sensor low (lean)
P0132 Engine running rich
P0134 Front 02 sensor open/not responding
P0151 Rear 02 sensor low (lean)
P0152 Rear 02 sensor high (rich)
P0154 Rear 02 sensor open/not responding
P0261 Front Injector Open/Low EFI
P0262 Front Injector High EFI
P0263 Rear Injector Open/Low EFI
P0264 Rear Injector High EFI
P0373 CKP Sensor Intermittent Carb
P0373 CKP Sensor Intermittent EFI
P0374 CKP Sensor Not Detected Carb
P0374 CKP Sensor Sync Error EFI
P0501 VSS Low Carb
vP0501 VSS Low EFI
P0502 VSS High/Open Carb
P0502 VSS High/Open EFI
P0505 Loss of Idle Speed Control EFI
P0562 Battery Voltage Low Carb
P0562 Battery Voltage Low EFI
P0563 Battery Voltage High Carb
P0563 Battery Voltage High EFI
P0602 Calibration Memory Error Carb
P0603 EEPROM Failure Carb
P0603 ECM EEPROM Error EFI
P0604 RAM Failure Carb
P0605 Program Memory Error Carb
P0605 ECM Flash Error EFI
P0607 Converter Error Carb
P0661 Intake solenoid low/open
P0662 Intake solenoid high/shorted
P1001 System Relay Coil Open/Low EFI
P1002 System relay Coil High/Shorted EFI
P1003 System relay Contacts Open EFI
P1004 System Relay Contacts Closed EFI
P1009 Incorrect Password Carb
P1009 Incorrect Password EFI
P1010 Missing Password Carb
P1010 Missing Password EFI
P1351 Front Ignition Open/Low Carb
P1351 Front Ignition Open/Low EFI
P1352 Front Ignition Coil High/Shorted Carb
P1352 Front Ignition Coil High/Shorted EFI
P1353 Front Cylinder No Combustion EFI
P1354 Rear Ignition Coil Open/Low Carb
P1354 Rear Ignition Coil Open/Low EFI
P1355 Rear Ignition Coil High/Shorted Carb
P1355 Rear Ignition Coil High/Shorted EFI
P1356 Rear Cylinder No Combustion EFI
P1357 Intermittent Secondary Front EFI
P1358 Intermittent Secondary Rear EFI
U1016 Loss of ICM/ECM Serial Data Instruments
U1016 Loss of ECM Serial Data, Vehicle Speed, Vehicle Inhibit Motion or Power train Security Status TSM/TSSM
U1064 Loss of TSM/TSSM Serial Data Carb
U1064 Loss of TSM/TSSM Serial Data EFI
U1064 Loss of TSM/TSSM Serial Data Instruments
U1097 Loss of Speedometer Serial data Carb
U1097 Loss of Speedometer Serial data EFI
U1097 Loss of Speedometer Serial data TSM/TSSM
U1255 Missing Message at Speedometer EFI
U1255 Serial Data Error/Missing Message EFI
U1255 Serial Data Error/Missing Message Instruments
U1255 Serial Data Error/Missing Message TSM/TSSM
U1300 Serial Data Low Carb
U1300 Serial Data Low EFI
U1300 Serial Data Low Instruments
U1300 Serial Data Low TSM/TSSM
U1301 Serial Data Open/High Carb
U1301 Serial Data Open/High EFI
U1301 Serial Data Open/High Instruments
U1301 Serial Data Open/High TSM/TSSM
2006 models with 02 sensors (Dynas)
P0131 Front 02 sensor lean for any length of time
P0151 Rear 02 sensor lean for any length of time
Above codes can also be set if 02 sensor fails.
AFR – Air Fuel Ratio
ATS – Air Temperature Sensor
BAS – Bank Angle Sensor
CCM – Cruise Control Module
CKP – Crank Position Sensor. The CKP generates an “AC signal” which is sent to the ECM where it is used to reference engine position (TDC) and speed. Home position established by taking readings off the 22 teeth on the alternator rotor.
DTC – Diagnostic Trouble Codes
ECM – Electronic Control Module. (The Computer) Computes the spark advance for proper ignition timing and fuel control based on sensor inputs (from CKP, MAP & TP sensors) and controls the low-voltage circuits for the ignition coils and injectors. The dwell time for the ignition coil is also calculated in the microprocessor and is dependent upon battery voltage. The programmed dwell feature gives adequate spark at all speeds.
ECT – Engine Coolant Temperature. Sensor also controls the cooling fan relay that provides 12 Vdc to the fans.
EFI – Electronic Fuel Injection
EFP – Electronic Fuel Pump
ET – Engine Temperature sensor
FI – Fuel Injectors
FPR – Fuel Pressure regulator
IAC – Idle Air Control actuator
IAT – Intake Air Temperature sensor
ISS – Ion Sensing System…detonation detection
MAP – manifold Absolute Pressure sensor. The MAP sensor monitors the intake manifold pressure (vacuum) and sends the information to the ECM. The EMC then adjusts the spark and fuel-timing advance curves for optimum performance.
TP – Throttle Position Sensor
TSM/TSSM (Turn Signal/ Turn Signal Security Module)
VE – Volume Efficiency
VSS – Vehicle Speed Sensor. Used as an input for idle speed control
2007-09 DTC’s
Here’s the listing of the diagnostic Harley error codes (DTC codes). Some are similar to the 07 and previous years but there are some new codes too. Some even cross over into the 07 bikes and are not listed for the 07 bikes.
The IM (instrument module) is capable of displaying DTC’s (diagnostic trouble codes).
Speedometer Self Diagnostics: The speedometer is capable of displaying and clearing speedometer, tachometer, TSM/TSSM and ICM/ECM Diagnostic Trouble Codes (DTC).
1 – Turn Ignition switch to OFF & Run/Stop switch is to Run.
2 – Push odometer reset button in & hold.
3 – Turn ignition switch to Ignition and relea
se odometer reset button. Background lighting sould illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word “diag” should then appear.
4 – Push the odometer reset button once and you will see the selection menu “PSSPt” with the first P flashing.
5 – Each letter represents an area of the diagnostics module. The module that is flashing is the one you are going to check. To move from one letter (module) to the next, you push the odometer reset button one time. (from P to S to SP to t and back to P, etc.)
- P = ECM/ICM (Electronic Control Module [EFI] / Ignition Control Module [Carbureted])
- S = TSM/TSSM (Turn Signal/ Turn Signal Security Module)
- SP = speedometer
- T = tachometer
6 – To get the DTC within an area of diagnostics, push and hold the odometer reset button in for 5 seconds and release. If there are any DTCs the code will be displayed or the word “none” will appear if there are no DTCs. Push the odometer reset button again to view additional codes if they exist.
7 – Record the codes.
8 – If DTCs are not to be cleared, Press and release the odometer reset button. Part number of module will be displayed.
NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until ‘clear’ comes up. Release the odometer reset button. Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTCs again by repeating steps 1 to 9. If the code is current it will reappear.
9 – Press and release the odometer reset button to continue to the next module.
10 – Turn Ignition switch to OFF.
On models not equipped with a tachometer, “No Rsp” will appear when the tachometer identifier is selected. “No Rsp” (no response) will also appear if the run/off switch is in the off position when doing this procedure.
HFSM = Hands Free Security Module
TSM = Turn signal module
Priority/DTC/Fault condition
1. P0605 ECM FLASH Memory Error
2. P0603 ECM EEPROM Memory Error
3. U1300 ECM Serial Data Low
4. U1301 ECM Serial Data High
5. U1097 Loss of Speedometer Serial Data to ECM
6. U1064 Loss of TSM/FSFM Serial Data to ECM
7. P1003 System relay contacts open
8. P1002 System Relay Coil High/Shorted
9. P1001 System Relay Coil Open/Low
10. P1004 System Relay Contacts Closed
11. P1009 Incorrect Password
12. P1010 Missing Password
13. P06415 V+Vref 1 Out Of Range
14. P06515 V+Vref 2 Out Of Range
15. P0373 CKP Sensor Intermittent
16. P0107 Map Sensor Open/Low
17. P0108 Map Sensor High
18. P0374 CKP Sensor Synch Error
19. P1511 Throttle actuator control power management failure of throttle control actuator
20. P1600 EFI Module Processor Internal Error
21. P1270 TGS Validation Error
22. P2107 EFI Module Processor Internal Fault
23. P2101 throttle actuator control motor circuit range/performace error
24. P2122 TGS1 Low/Open
25. P2123 TGS1 High
26. P2127 TGS2 Low/Open
27. P2128 TGS2 High
28. P2138 TGS Correlation Error (Twist grip sensor)
29. P0120 TPS1 Range Error
30. P0220 TPS2 Range Error
31. P0122 TPS1 Low
32. P0123 TPS2 High/Open
33. P0222 TPS2 Low
34. P0223 TPS2 High/Open
35. P2135 TPS Correlation Error
36. P2119 EFI Motor Throttle Body Range Performance
37. P2100 EFI Motor Circuit Open
38. P2101 EFI Motor Circuit Range Performance (Actuation Error)
39. P2102 EFI Motor Circuit Low
40. P2103 EFI Motor Circuit High
41. P2176 EFI Closed Position Not Learned
42. P1514 Air Flow Fault
43. P2105 EFI Forced engine shutdown
44. P1501 Jiffy Stand Sensor Low
45. P1502 Jiffy Stand Sensor High
46. P0572 Brake Switch Low
47. P0117 ET Sensor Low
48. P0118 ET Sensor High
49. P0112I AT Voltage Low
50. P0113I AT Voltage Open/High
51. P1351 Front Ignition Coil Driver Open/Low
52. P1354 Rear Ignition Coil Driver Open/Low
53. P1352 Front Ignition Coil Driver High/Shorted
54. P1355 Rear Ignition Coil Driver High/Shorted
55. P1357 Front Cylinder Combustion Intermittent
56. P1358 Rear Cylinder Combustion Intermittent
57. P0261 Front Injector Open/Low
58. P0263 Rear Injector Open/Low
59. P0262 Front Injector High
60. P0264 Rear Injector High
61. P0562 Battery Voltage Low
62. P0563 Battery Voltage High
63. P0501 VSS Sensor Low
64. P0502 VSS Sensor High/Open
65. P1356 Rear Cylinder No Combustion
66. P1353 Front Cylnder No Combustion
67. P0444 Purge Solenoid Open/Low
68. P0445 Purge Solenoid High
69. P1475 Exhaust Actuation Position Error
70. P1477 Exhaust Actuator Open/Low
71. P1478 Exhaust Actuator Shorted/High
72. P0131 Front Oxygen Sensor Low
73. P0151 Rear Oxygen Sensor Low
74. P0132 Front Oxygen Sensor High
75. P0152 Rear Oxygen Sensor High
76. P0134 Front Oxygen Sensor Inactive
77. P0154 Rear Oxygen Sensor Inactive
78. P1510 EFI Limited Performance Mode
79. P1511 EFI Power Management Mode
80. P1512 EFI Forced Idle Mode
81. P0577 Cruise Control Input High
Priority/DTC/Fault condition
HFSM = Hands Free Security Module
TSM = Turn signal module
1. U1300 Serial Data Low
2. U1301 Serial Data High
3. U1016 Loss of ECM Serial Data
4. U1255 Serial Data Error
5. B1142 Smart Security System Internal Fault
6. B1135 Accelerometer Failed
7. B1136 (HFSM)Accelerometer Tip Test Error
8. B1151 Bank Angle Sensor (BAS) Short to Ground
9. B1152 Bank Angle Sensor (BAS) Short to Battery
10. B1153 Bank Angle Sensor (BAS) High
11. B1154 Clutch Switch Input Short to Ground
12. B1155 Neutral Switch Input Short to Battery
13. B1134 Starter Output High
14. B1121 (TSM)Left Turn Output Fault
B1121 (HFSM)Left Turn Output Open
15. B1122 (TSM)Right Turn Output Fault
B1122 (HFSM)Right Turn Output Open
16. B1123 (HFSM)Left Turn Output Short to Ground
17. B1124 (HFSM)Right Turn Output Short to Ground
18. B1125 (HFSM)Left Turn Output Short to Battery
19. B1126 (HFSM)Right Turn Output Short to Battery
20. B1143 (HFSM)Security Antenna Short to Ground
21. B1144 (HFSM)Security Antenna Short to Battery
22. B1145 (HFSM)Security Antenna Open
23. B0563 Battery Voltage High
24. B1131 (HFSM)Alarm Output Low
25. B1132 (HFSM)Alarm Output High
26. B1141 (TSM)Ignition Switch Low/Open
B1141 (HFSM)Ignition Switch Low/Open
ABS section of the 2008 Electrical Diagnostics
C0562 Device voltage low
C0563 System voltage high
C1014 ECU internal fault
C1017 Pump motor power circuit open fault
C1018 Pump motor ground high resistance fault
C1021 Front wheel speed sensor equals 0
C1023 Rear wheel speed sensor equals 0
C1025 Front wheel speed signal intermittent
C1027 Rear wheel speed signal intermittent
C1032 Front wheel speed sensor circuit open or shorted
C1034 Rear wheel speed sensor circuit open or shorted
C1042 Pump motor open
C1043 Pump motor stalled
C1055 ECU internal fault
C1056 ECU internal fault
C1057 ECU internal fault
C1061 ECU internal fault
C1062 ECU internal fault
C1065 ECU internal fault
C1066 ECU internal fault
C1094 Front brake switch always on
C1095 Front brake switch open
C1118 ECU internal fault
C1121 ECU internal fault
C1151 Front wheel release too long
C1153 Rear wheel release too long
C1158 Calibration programming required
C1206 Wheel speed sensor frequency out of range
C1208 Wheel speed sensor frequency out of range
C1212 Front or rear brake not applied with decel
C1214 Rear brake switch always on
C1216 Rear brake switch open
U1300 Serial data low
U1301 Serial data open/high
SPEEDOMETER TROUBLE CODES
CODE – TROUBLE – WIRE COLOR
d01 – speed sensor power output shorted low – red
d02 – speed sensor power output shorted high – red
d03 – not used
d04 – not used
d05 – speed sensor return shorted high – white
d06 – speed sensor return shorted low – white
d07 – not used
d08 – peedometer power overvoltage – orange/white
d09 – speed output shorted high – white/green
d10 – speed output shorted low or open – white/green
5 digit number – speedometer pulses per unit
00-03 Harley Davidson Motorcycles
Remove right side saddlebag and side cover if so equipped. Remove protective plug from data link connector. Other models will be under the seat. To activate the diagnostic feature,follow these steps.
a. Create diagnostic test wire or use a female spade clip which will bridge the two terminals perfectly.
b. Install diagnostic test wire/clip across Terminals 1 and 2 on the data link connector, they are marked.
c. Turn Ignition/Light Key Switch to IGNITION and wait approximately 10 seconds (4 seconds lamp ON, 6 seconds lamp OFF) for check engine lamp to start flashing.
All trouble codes are sent out as a series of flashes. To retrieve the first digit of the trouble code simply observe the number of times the lamp flashes.
a. The lamp will then flash one or more times to indicate the first digit of the trouble code.
b. The length of time the lamp is illuminated and the length of time in which it is off are each about 0.5 second in duration.
The second digit follows:
a. Following the transmission of the first digit, there is a 1.2 second pause in which the lamp is off.
b. The lamp will then flash one or more times to indicate the second digit of the trouble code. Count the number of times the lamp flashes to retrieve the second digit.
If more than one trouble code is sent:
a. Following transmission of the second digit of the first code, there is a 3 second pause in which the lamp is off.
b. Once all codes have been sent, the data string is repeated. When you have recorded the same trouble code twice, it is an indication that the transmission has been restarted and that all trouble codes have been retrieved.
IMPORTANT NOTE: If diagnostic test wire is installed across Pins 1 and 2 on connector in lieu of a Scanalyzer, the ECM is placed in a diagnostic test mode and the engine will start. The test wire must be removed from the data connector and the ignition switch turned OFF or the check engine lamp will continue to flash codes. A historic trouble code resides in the memory of the ECM until the code is cleared by use of the Scanalyzer or a total of 50 trips has elapsed. A “trip” consists of a start and run cycle, the run cycle lasting at least 30 seconds. After the 50 trip retention period, the trouble code is automatically erased from memory (that is, assuming no subsequent faults of the same type are detected in that period). The numbers after the ‘historic’ or ‘current’ is the speedo code number, but without the electrical diagnostics manual you’re not going to know what they mean.
1 Current 53 ECM flash error
2 Historic 53 ECM flash error
3 Current 54 ECM EEPROM error
4 Historic 54 ECM EEPROM error
5 Current 63 ECM serial data low
6 Current 63 ECM serial data open/high
7 Current 63 TSSM serial data low
8 Current 63 TSSM serial data open/high
9 Current 61 Loss of TSM/TSSM serial data
10 Current 14 Loss of all ECM serial data (state of health)10 24 Loss of vehicle speed10 33 Loss of vehicle inhibit motion10 43 Loss of powertrain security status
11 Current 33 System relay contacts open
12 Current 33 System relay coil high/shorted
13 Current 33 System relay coil open/low
14 Current 33 System relay contacts closed
15 Current 99 Incorrect password
16 Current 99 Missing password
17 Current 41 CKP sensor intermittent
18 Current 41 CKP sensor synch error
19 Current 11 TP sensor open/low
20 Current 11 TP sensor high
21 Current 12 MAP sensor open/low
22 Current 12 MAP sensor high
23 Current 14 ET sensor voltage low
24 Current 14 ET sensor open/high
25 Current 15 IAT sensor voltage low
26 Current 15 IAT sensor open/high
27 Current 24 Front ignition coil open/low
28 Current 25 Rear ignition coil open/low
29 Current 24 Front ignition coil high/shorted
30 Current 25 Rear ignition coil high/shorted
31 Current 24 Front cylinder combustion intermittent
32 Current 25 Rear cylinder combustion intermittent
33 Current 23 Front injector open/low
34 Current 32 Rear injector open/low
35 Current 23 Front injector high
36 Current 32 Rear injector high
37 Current 16 Battery voltage low
38 Current 16 Battery voltage high
39 Current 43 VSS sensor low
40 Current 43 VSS sensor high
41 Current N/A (no speedo code for this) Check engine light open/low NO CHECK ENGINE LAMP AT KEY ON or CHECK ENGINE LAMP ON CONTINUOUSLY
42 Current N/A (no speedo code for this) Check engine light high NO CHECK ENGINE LAMP AT KEY ON
43 Current 35 Tachometer low
44 Current 35 Tachometer high
45 Current 25 Rear cylinder no combustion
46 Current 24 Front cylinder no combustion
47 Current 34 Loss of idle speed control IDLE AIR CONTROL
48 Current 35 Accelerometer fault
49 Current 34 Starter output high
50 Current 25 Ignition enable output high
51 Current 21 Left turn output fault
52 Current 22 Right turn output fault
53 Current 11 Battery voltage high
54 Current 31 Alarm output low
55 Current 32 Alarm output high
56 Current 41 Ignition switch open/low
57 Historic 63 ECM serial data low
58 Historic 63 ECM serial data open/high
59 Historic 63 TSSM serial data low
60 Historic 63 TSSM serial data open/high
61 Historic 61 Loss of TSM/TSSM serial data
62 Historic 14 Loss of all ECM serial data (state of health)
63 Historic 33 System relay contacts open
64 Historic 33 System relay coil high/shorted
65 Historic 33 System relay coil open/low
66 Historic 33 System relay contacts closed
67 Historic 99 Incorrect password
68 Historic 99 Missing password
69 Historic 41 CKP sensor intermittent
70 Historic 41 CKP sensor synch error
71 Historic 11 TP sensor open/low
72 Historic 11 TP sensor high
73 Historic 12 MAP sensor open/low
74 Historic 12 MAP sensor high
75 Historic 14 ET sensor voltage low
76 Historic 14 ET sensor open/high
77 Historic 15 IAT sensor voltage low
78 Historic 15 IAT sensor open/high
79 Historic 24 Front ignition coil open/low
80 Historic 25 Rear ignition coil open/low
81 Historic 24 Front ignition coil high/shorted
82 Historic 25 Rear ignition coil high/shorted
83 Historic 24 Front cylinder combustion intermittent
84 Historic 25 Rear cylinder combustion intermittent
85 Historic 23 Front injector open/low
86 Historic 32 Rear injector open/low
87 Historic 23 Front injector high
88 Historic 32 Rear injector high
89 Historic 16 Battery voltage low
90 Historic 16 Battery voltage high
91 Historic 43 VSS sensor low
92 Historic 43 VSS sensor high
93 Historic N/A Check engine light open/low NO CHECK ENGINE LAMP AT KEY ON or CHECK ENGINE LAMP ON CONTINUOUSLY
94 Historic N/A Check engine light high NO CHECK ENGINE LAMP AT KEY ON
95 Historic 35 Tachometer low
96 Historic 35 Tachometer high
97 Historic 25 Rear cylinder no combustion
98 Historic 24 Front cylinder no combustion
99 Historic 34 Loss of idle speed control
100 Historic 35 Accelerometer fault
101 Historic 34 Starter output high
102 Historic 25 Ignition enable output high
103 Historic 21 Left turn output fault
104 Historic 22 Right turn output fault
105 Historic 11 Battery voltage high
106 Historic 31 Alarm output low
107 Historic 32 Alarm output high
108 Historic 41 Ignition switch open/low
| Текущее время: 23 июн 2023, 06:03 |
VRSC — коды ошибок, диагностика ECM
|
Страница 1 из 1 | [ Сообщений: 16 ] |
VRSC — коды ошибок, диагностика ECM
| Автор | Сообщение |
|---|---|
|
Зарегистрирован: 13 мар 2013, 13:50 |
Коды ошибок можно проверить сдесь http://www.1130cc.com/?page=codes Мотобратве желаю их отсутсвия… Reading codes The IM (instrument module) is capable of displaying DTC’s (diagnostic trouble codes). 1- Ignition off Codes List of all v-rod fault codes RANKING DTC STATUS FAULT CONDITION SOLUTION 49 P1652 Current Check engine light high 4.6 IM SELF DIAGNOSTICS |
| 14 мар 2013, 11:02 |
|
 |
|
|
MadMax АДМИНИСТРАТОР Зарегистрирован: 31 мар 2011, 11:34 |
Уважаемый Адмирал! Раз уж этот материал здесь, то неплохо бы вклеить сюда всю таблицу. Я ее вставлю в первый пост. От себя добавлю к тому, что по ссылке. Кроме того, интерфейсная диагностика доступна не только владельцам VRSC, но и водителям всех остальных впрысковых Харлеев. Различия в описании кодов. Полную диагностику кодов неисправностей можно сделать только сервисным сканером или компьютером. |
| 14 мар 2013, 13:29 |
|
|
|
|
Admiral Зарегистрирован: 13 мар 2013, 13:50 |
ОК ! Таблица у меня есть в pdf и в txt, но этот формат запрещен — выложил ссылку на сайт заокеанских однополчан. Спасибо за разверную рецензию. |
| 14 мар 2013, 14:49 |
|
|
|
|
мари-хуанна Зарегистрирован: 10 июл 2017, 12:25 |
ХЭЛП народ |
| 15 май 2018, 14:00 |
|
|
|
|
koc911 Зарегистрирован: 05 окт 2016, 10:41 |
мари-хуанна писал(а): ХЭЛП народ C codes indicate an issue with ABS C0562 — ABS voltage low |
| 15 май 2018, 14:26 |
|
|
|
|
мари-хуанна Зарегистрирован: 10 июл 2017, 12:25 |
спасибо |
| 16 май 2018, 08:27 |
|
|
|
|
Woorhees Зарегистрирован: 18 июн 2011, 08:42 |
Поиском нашел только эту тему. Моя Электра 05 года выдает ошибку — После ее удаления и некоторого времени она не появляется. Что может не сгорать в переднем цилиндре и как это обнаружить? Добавлю, при покупке мотоцикла были еще ошибки: Р0374, Р1356, U1097 |
| 27 апр 2020, 16:38 |
|
|
|
|
Lukich Зарегистрирован: 06 июн 2012, 01:33 |
от свечей и проводов, до перепрошивки на более свежий софт. Надо копать. По английски куча инфы, но там много бреда, типа у кого-то забился топливный разъем итд. А реально есть пропуски? Я бы начал с уменьшения/увеличения зазора на свечах или их замены, т.к. этот код определяется по-моему по току между электродами. А на это влияет мощность искры катушки, тип проводов, состав смеси в цилиндре. Кстати Р1356 — это по-видимому такой же код в заднем цилиндре. (мануал не читаю, лень рыться, по памяти и гуглом сейчас ищу) |
| 28 апр 2020, 11:17 |
|
|
|
|
ThE0ReTiC Зарегистрирован: 03 ноя 2013, 23:28 |
Woorhees писал(а): Поиском нашел только эту тему. Моя Электра 05 года выдает ошибку — Начни со свечей и проводов. Провод должен иметь определенное номинальное сопротивление. |
| 28 апр 2020, 11:35 |
|
|
|
|
Woorhees Зарегистрирован: 18 июн 2011, 08:42 |
Lukich писал(а): А реально есть пропуски? Я бы начал с уменьшения/увеличения зазора на свечах или их замены, т.к. этот код определяется по-моему по току между электродами. А на это влияет мощность искры катушки, тип проводов, состав смеси в цилиндре. Кстати Р1356 — это по-видимому такой же код в заднем цилиндре. (мануал не читаю, лень рыться, по памяти и гуглом сейчас ищу) Да, Р1356 это по заднему цилиндру. |
| 28 апр 2020, 12:01 |
|
|
|
|
dimidrol Зарегистрирован: 12 ноя 2014, 23:36 |
К выще перечисленному добавлю,что находил пропуски при перетертом шланге подачи топлива в баке,при проблеме быстросъемного штуцера томливоподачи снаружи бака,переставал пропускать нужное количество топлива. |
| 28 апр 2020, 12:27 |
|
|
|
|
Woorhees Зарегистрирован: 18 июн 2011, 08:42 |
dimidrol писал(а): К выще перечисленному добавлю,что находил пропуски при перетертом шланге подачи топлива в баке,при проблеме быстросъемного штуцера томливоподачи снаружи бака,переставал пропускать нужное количество топлива. Но, как я понимаю, если мотору не хватает топлива, он будет троить постоянно и разгоняться вообще не будет. Но все равно спасибо. Проверю. |
| 28 апр 2020, 12:52 |
|
|
|
|
ThE0ReTiC Зарегистрирован: 03 ноя 2013, 23:28 |
Woorhees писал(а): dimidrol писал(а): К выще перечисленному добавлю,что находил пропуски при перетертом шланге подачи топлива в баке,при проблеме быстросъемного штуцера томливоподачи снаружи бака,переставал пропускать нужное количество топлива. Но, как я понимаю, если мотору не хватает топлива, он будет троить постоянно и разгоняться вообще не будет. Но все равно спасибо. Проверю. Нет, не постоянно. и провалы при разгоне могут спорадически возникать на самом деле. |
| 28 апр 2020, 14:03 |
|
|
|
|
Woorhees Зарегистрирован: 18 июн 2011, 08:42 |
И так, проверив ВВ провода (в норме), сменив свечи, при разгоне ошибка не появояется, но чихание переодически проявляется. Это можно заметить, когда в пробках перегазовываю для привлечения внимания. Давеча, как то разогнавшись до отсечки на второй передаче, а это 6500 у меня, мотор просто резко заглох, загорелся чек. В общем до обочины я доехал булькая одним цилиндром. Вроде на заднем. Из переднего пошел черный дым и сильно запахло бензином. Выскочили ошибки 1353 и 1356. Я их стёр, мотоцикл вновь ожил. После этого проехал ещё 500 км. Чихнул только один раз у меня за все время. Обороты в диапазоне 3000-4000 при разгонах. Выше побаиваюсь уже. И вот теперь не знаю куда копать. |
| 28 июл 2020, 09:39 |
|
|
|
|
Lukich Зарегистрирован: 06 июн 2012, 01:33 |
провода проверяются заменой на другой комплект. Так проверял, или тестером тыкал? Далее можно попробовать форсунки махнуть местами. ПОнаблюдать за цветом свечей до и после. Катушка не помню — менялась или нет? Р0374 точно больше не появлялась? А то заставлю осциллограф юзать. |
| 29 июл 2020, 00:54 |
|
|
|
|
Woorhees Зарегистрирован: 18 июн 2011, 08:42 |
Провода проверялись заменой. Свечи когда менял были черные. |
| 01 авг 2020, 18:03 |
|
|
|
| Показать сообщения за: Поле сортировки |
VRSC — коды ошибок, диагностика ECM
|
|
Страница 1 из 1 | [ Сообщений: 16 ] |
Кто сейчас на конференции |
|
Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 1 |
| Вы не можете начинать темы Вы не можете отвечать на сообщения Вы не можете редактировать свои сообщения Вы не можете удалять свои сообщения Вы не можете добавлять вложения |
Harley Fault Codes 2004-2015
Below is a list of comprehensive list of diagnostic codes that you may come across on your
Harley-Davidson.
- Sensors and Motors (P0051-P2304)
- ABS (C0652-C1573)
- Battery, Ignition, Lighting and
Accessories (B0563-B2274) - CanBus (U0001-U1317)
- Radio Diagnostics (B2006-B2027)
How to Read Error Codes
- With the ignition in the off position, press and hold the trip meter button, and turn the ginition swith to the on position.
- Release the button. Your speedo indicators should illuminate and the needle should do a full sweep.
- “diag” will appear on the odometer screen. Press the trip button once.
- “PSSPt” is now displayed. Each of the letters represents a different area.
-
P = ECM / ICM (Engine / Ignition Control Module)
-
S = TSM / TSSM (Turn Signal / Turn Signal Security Module)
-
SP = Speedometer
-
t = Tachometer
-
- You can highlight each area by pressing the button. Once the area you wish to select is highlighted, press and hold the
button for 5 seconds. - If there are any codes, you will be able to go through them one at a time by pressing the button. Once you have them
recorded, they can be cleared by holding the button for more than 5 seconds. Once “clear” is on the screen, press the button once more. - To exit the Diagnostic Mode, turn the ignition switch off.
Harley Sensor and Motor Codes
| POO51 | Heater Control Circuit 02 Sensor Low |
| PO106 | Map Sensor Rate of Range Error |
| P0107 | Map Sensor Failed Open/Low |
| P0108 | Map Sensor Failed High |
| P0112 | IAT Sensor Voltage Low |
| P0113 | IAT Sensor Voltage Open / High |
| P0117 | ET Sensor Voltage Low |
| P0118 | ET Sensor Voltage Open / High |
| P0120 | TPS1 Range Error TPS |
| P0122 | TPS1 Low TPS |
| P0123 | TPS1 High / Open TPS |
| P0131 | Front 02 Sensor Low (lean) |
| P0132 | Front 02 Sensor High (rich) |
| P0134 | Front 02 Sensor Open / Not Responding |
| P0151 | Rear 02 Sensor Low (lean) |
| P0152 | Rear 02 Sensor High (rich) |
| P0154 | Rear 02 Sensor Open / Not Responding |
| P0220 | TPS2 Range Error |
| P0222 | TPS2 Low TPS |
| P0223 | TPS2 High/Open |
| P0261 | Front Injector Open/Low |
| P0262 | Front Injector High |
| P0263 | Rear Injector Open/Low |
| P0264 | Rear Injector High (CAN-Bus) |
| P0264 | Rear Injector Open/Low |
| P0265 | Rear Injector High |
| P0371 | Crank Position Sensor, Too Many Pulses |
| P0372 | Crank Position Sensor, Too Few Pulses |
| P0373 | CKP Sensor Intermittent |
| P0374 | CKP Sensor Not Detected |
| P0444 | Purge Solenoid (Evap. Canister) Open/Low |
| P0445 | Purge Solenoid (Evap. Canister) High |
| P0501 | VSS Low |
| P0502 | VSS High/Open (Can-Bus) |
| P0502 | VSS Speed Failed Low |
| P0503 | VSS Speed Failed High |
| P0505 | Loss of Idle Speed Control |
| P0506 | Idle Speed Control RPM Too Low |
| P0507 | Idle Air Control System RPM Higher Than Expected |
| P0562 | Battery Voltage Low |
| P0563 | Battery Voltage High |
| P0572 | Brake Switch Low |
| P0577 | Cruise Control Input High |
| P0602 | Calibration Memory Error |
| P0603 | ECM EEPROM Failure |
| P0604 | RAM Failure |
| P0605 | ECM Flash Error |
| P0607 | Converter Error |
| P0641 | 5V+Vref 1 Out of Range |
| P0651 | 5V+Vref 2 Out of Range |
| P0661 | Intake Solenoid Low/Open |
| P0662 | Intake Solenoid High/Shorted |
| P1001 | System Relay Coil Open/Low |
| P1002 | System Relay Coil High/Shorted |
| P1003 | System Relay Contacts Open |
| P1004 | System Relay Contacts Closed |
| P1009 | Incorrect Password |
| P1010 | Missing Password |
| P1270 | TGS Validation Error |
| P1351 | Front Ignition Open/Low |
| P1352 | Front Ignition Coil High/Shorted |
| P1353 | Front Cylinder No Combustion |
| P1354 | Rear Ignition Coil Open/Low |
| P1355 | Rear Ignition Coil High/Shorted |
| P1356 | Rear Cylinder No Combustion |
| P1357 | Front Intermittent Secondary Combustion |
| P1358 | Rear Intermittent Secondary Combustion |
| P1475 | Exhaust Actuation Position Error |
| P1477 | Exhaust Actuator Open/Low |
| P1478 | Exhaust Actuator Shorted/High |
| P1501 | Jiffy Stand Sensor Low |
| P1502 | Jiffy Stand Sensor High |
| P1510 | EFI Limited Performance Mode (TBW) |
| P1511 | EFI Power Management Mode |
| P1512 | EFI Forced Idle Mode |
| P1514 | Air Flow Fault (TBW) |
| P1600 | EFI Module Processor Internal Error |
| P1632 | Odometer Learned Up |
| P2100 | EFI TCA Motor Circuit Open (TBW) |
| P2101 | EFI TCA Motor Circuit Range/Performance |
| P2102 | EFI TCA Motor Circuit Low |
| P2103 | EFI TCA Motor Circuit High |
| P2105 | EFI Forced Engine Shutdown |
| P2107 | EFI Module Control Processor Internal Fault |
| P2119 | EFI Motor Throttle Body Range Performance (TBW) |
| P2122 | TGS1 Low/Open |
| P2123 | TGS1 High |
| P2127 | TGS2 Low/Open |
| P2128 | TGS2 High |
| P2135 | TPS Voltage Correlation Error |
| P2138 | TGS Voltage Correlation Error |
| P2176 | EFI Closed Postion Not Learned |
| P2300 | Front Ignition Coil Driver Low/Open |
| P2301 | Front Ignition Coil Driver High/Shortened |
| P2303 | Rear Ignition Coil Driver Low/Open |
| P2304 | Rear Ignition Coil Driver High/Shortened |
Harley ABS and Power
Circuit Codes
| C0562 | Device Voltage Low |
| C0563 | Device Voltage High |
| C1014 | ECU Internal Fault ABS |
| C1017 | Pump Motor Power Circuit Fault |
| C1018 | Pump Motor Ground High Resistance Fault |
| C1021 | Front Wheel Speed Sensor Equals Zero |
| C1023 | Rear Wheel Speed Sensor Equals Zero |
| C1025 | Front Wheel Speed Signal Intermittent |
| C1027 | Front Wheel Speed Frequency Out Of Range |
| C1032 | Front Wheel Speed Sensor Open or Shorted |
| C1034 | Rear Wheel Speed Sensor Open or Shorted |
| C1041 | Rear Actuator Circuit Low/Open |
| C1042 | Front Actuator Circuit Open |
| C1043 | Pump Motor Stalled |
| C1044 | Rear Actuator Circuit Open |
| C1052 | Rear Actuator Circuit High |
| C1055 | ABS ECU Internal Fault |
| C1066 | ECU Internal Fault |
| C1094 | Front Brake Switch Always On |
| C1095 | Front Brake Switch Open |
| C1102 | Rear Actuator Motor Stalled |
| C1118 | ECU Internal Fault |
| C1121 | ECU Internal Fault |
| C1151 | Front Wheel Release Too Long |
| C1153 | Rear Wheel Release Too Long |
| C1158 | Calibration Programming Required |
| C1178 | No VIN Received From ECM |
| C1184 | VIN Does Not Match ABS ECU Calibration |
| C1192 | Front Actuator Circuit High |
| C1193 | Front Actuator Motor Stalled/td> |
| C1206 | Front Wheel Speed Sensor Frequency Out of Range |
| C1207 | Rear Wheel Speed Signal Intermittent |
| C1208 | Rear Wheel Speed Sensor Frequency Out of Range |
| C1212 | Front or Rear Brake not Applied With Decel |
| C1214 | Rear Brake Switch Always On |
| C1216 | Rear Brake Switch Open |
| C1222 | ABS Voltage Low Terminal 11 |
| C1223 | ABS Voltage Low Terminal 20 |
| C1224 | Front Actuator Power Shorted High |
| C1225 | Rear Actuator Power Shorted High |
| C1561 | Front Apply Solenoid Circuit Open or High |
| C1562 | Front Apply Solenoid Circuit Shorted Low |
| C1563 | Front Solenoid Circuit Shorted High |
| C1564 | Front Release Solenoid Circuit Open or High |
| C1565 | Front Release Solenoid Circuit Shorted Low |
| C1567 | Rear Apply Solenoid Circuit Open or High |
| C1568 | Rear Apply Solenoid Circuit Shorted Low |
| C1571 | Rear Solenoid Circuit Shorted High |
| C1572 | Rear Release Solenoid Circuit Open or High Resistance |
| C1573 | Rear Realease Solenoid Circuit Shorted Low |
Harley
Battery, Ignition, Lighting Codes
| B0563 | Battery Voltage High TSM / TSSM |
| B1004 | Fuel Level Sending Unit Low Instruments |
| B1005 | Fuel Level Sending Unit High / Open |
| B1006 | Accessory Line Overvoltage |
| B1007 | Ignition Line Overvoltage Instruments |
| B1008 | Reset Switch Closed Instruments |
| B1101 | LHCM Turn Signal Bulb Out |
| B1103 | LHCM Internal Fault |
| B1121 | Left Turn Output Fault TSM / TSSM |
| B1122 | Right Turn Output Fault TSM / TSSM |
| B1123 | Left Turn Output Short to Ground TSM/TSSM |
| B1124 | Right Turn Output Short to Ground TSM/TSSM |
| B1125 | Left Turn Output Short to Battery TSM/TSSM |
| B1126 | Right Turn Output Short to Battery TSM/TSSM |
| B1131 | Alarm Output Low TSSM |
| B1132 | Alarm Output High TSSM |
| B1134 | Starter Output High TSM/TSSM |
| B1135 | Accelerometer Fault TSM/TSSM |
| B1136 | Accelerometer Tip Test Error TSSM |
| B1141 | Ignition Switch Open / Low TSSM |
| B1142 | Smart Security System Internal Fault TSSM |
| B1143 | Security Antenna Short To Ground TSSM |
| B1144 | Security Antenna Short To Battery TSSM |
| B1145 | Security Antenna Open TSSM |
| B1151 | (Sidecar) BAS Low TSM/TSSM |
| B1151 | RHCM Turn Signal Bulb Out |
| B1152 | (Sidecar) BAS High TSM/TSSM |
| B1153 | (Sidecar) BAS Out Of Range TSM/TSSM |
| B1153 | RHCM Internal Fault |
| B1154 | Clutch Switch Input Short To Ground |
| B1155 | Neutral Switch Input Short To Battery |
| B1200 | Instrument Internal Fault |
| B1210 | Fuel Sender Shorted Low / Fuel Gauge Circuit |
| B1211 | Fuel Sender Shorted High / Open |
| B2102 | System Power Output Shorted High |
| B2103 | System Power Output Shorted Low |
| B2104 | System Power Output Overloaded |
| B2107 | Front Position / Running Power Output Shorted High |
| B2108 | Front Position / Running Power Output Shorted Low |
| B2109 | Front Position / Running Power Output Overloaded |
| B2112 | Accessory Output Shorted High |
| B2113 | Accessory Output Shorted Low |
| B2114 | Accessory Output Overloaded |
| B2116 | Fuel Pump Output Open |
| B2117 | Fuel Pump Output Shorted High |
| B2118 | Fuel Pump Output Shorted Low |
| B2119 | Fuel Pump Output Overloaded |
| B2121 | Starter Output Open/BCM Malfunction |
| B2122 | Starter Output Shorted High |
| B2123 | Starter Output Shorted Low |
| B2124 | Starter Output Overloaded |
| B2126 | Horn Output Open |
| B2127 | Horn Output Shorted High |
| B2128 | Horn Output Shorted Low |
| B2129 | Horn Output Overloaded |
| B2131 | High Beam Output Open |
| B2132 | High Beam Output Shorted High |
| B2133 | High Beam Output Shorted Low |
| B2134 | High Beam Output Overloaded |
| B2136 | Low Beam Output Open |
| B2137 | Low Beam Output Shorted High |
| B2138 | Low Beam Output Shorted Low |
| B2139 | Low Beam Output Overloaded |
| B2141 | Left Front Turn Signal Output Open |
| B2143 | Left Front Turn Signal Output Shorted Low |
| B2144 | Left Front Turn Signal Output Overloaded |
| B2146 | Right Front Turn Signal Output Open |
| B2148 | Right Front Turn Signal Output Shorted Low |
| B2149 | Right Front Turn Signal Output Overloaded |
| B2151 | Left Rear Turn Signal Output Open |
| B2153 | Left Rear Turn Signal Output Shorted Low |
| B2154 | Left Rear Turn Signal Output Overloaded |
| B2156 | Right Rear Turn Signal Output Open |
| B2158 | Right Rear Turn Signal Output Shorted Low |
| B2159 | Right Rear Turn Signal Output Overloaded |
| B2161 | Brake Lamp Output Open |
| B2163 | Brake Lamp Output Shorted Low |
| B2164 | Brake Lamp Output Overloaded |
| B2166 | Running Lights Output Open |
| B2168 | Running Lights Output Shorted High |
| B2169 | Running Lights Output Shorted Low |
| B2172 | Security Siren Output Shorted High |
| B2173 | Security Siren Output Shorted Low |
| B2176 | Security Antenna Output Open |
| B2177 | Security Antenna Output Shorted High |
| B2178 | Security Antenna Output Shorted Low |
| B2203 | Ignition Switch Input Shorted Low |
| B2206 | Engine Stop Switch Input Open/Shorted High |
| B2208 | Engine Stop Switch Input Shorted Low |
| B2218 | Neutral Switch Shorted Low |
| B2223 | Rear Brake Switch Shorted Low |
| B2250 | Clutch Switch Stuck |
| B2251 | Horn Switch Stuck |
| B2252 | High Beam Switch Stuck |
| B2253 | Low Beam Switch Stuck |
| B2254 | Left Turn Switch Stuck |
| B2255 | Trip Switch Stuck |
| B2260 | Start Switch Stuck |
| B2261 | Right Turn Switch Stuck |
| B2262 | Front Brake Switch Stuck |
| B2263 | Hazard Switch Stuck |
| B2270 | BCM Internal Fault |
| B2271 | BCM Low Voltage |
| B2272 | BCM or Speedometer Voltage High |
| B2274 | Constant Battery Line Fault |
Harley CAN Bus Codes
| U0001 | CAN bus Fault |
| U0011 | CAN bus Low Shorted / Can bus High |
| U0100 | Lost Communication With ECM |
| U0121 | Lost Communication With ABS |
| U0140 | Lost Communication With BCM |
| U0141 | Lost Communication With LHCM |
| U0142 | Lost Communication With RHCM |
| U0156 | Lost Communication With Speedometer |
| U1016 | Loss of ICM/ECM Serial Data |
| U1040 | Loss OF Communication With ABS |
| U1064 | Loss Of TSM/TSSM Serial Data |
| U1097 | Loss Of Speedometer Serial Data |
| U1255 | Missing Message at Speedometer EFI |
| U1300 | Serial Data Low |
| U1301 | Serial Data Open/High |
| U1302 | Infotainment Bus Off |
| U1306 | Infotainment Bus Lost Communication With Handsfree Phone |
| U1307 | Infotainment Bus Lost Communication With CB |
| U1308 | Infotainment Bus Lost Communication With Future |
| U1312 | Infotainment Bus Lost Communication With Future |
| U1313 | Infotainment Bus Lost Communication With Radio Satellite |
| U1314 | Infotainment Bus Lost Communication With Navigation |
| U1317 | Infotainment Bus Lost Communication With High-Out Amplifier |
Harley Radio Diagnostic
| B2006 | Radio Switch Stuck or Open |
| B2007 | Handlebar Switch Shorted High |
| B2008 | Handlebar Switch Shorted Low |
| B2009 | Handlebar Switch Stuck or Open |
| B2010 | Passenger Switch Shorted High |
| B2011 | Passenger Switch Shorted Low |
| B2012 | Passenger Switch Stuck or Open |
| B2013 | Sidecar Switch Shorted High |
| B2014 | Sidecar Switch Shorted Low |
| B2015 | Sidecar Switch Stuck or Open |
| B2016 | Front Speaker Shortened R1.0 Ohm When Setup |
| B2017 | Front Speaker Opened R>100 Ohms Tested Once per Ignition Cycle Ignition ON after Ignition Off for 10 sec. |
| B2018 | Front Speaker Shortened to Ground Ignition ON After Ignition OFF for 10 sec. |
| B2019 | Front Speaker Shortened to Battery Ignition ON After Ignition OFF for 10 sec. |
| B2020 | Rear Speaker Shortened R1.0 Ohm When Setup |
| B2021 | Rear Speaker Opened R>100 Ohms Tested Once Per Ignition Cycle Ignition ON After Ignition |
| B2022 | Rear Speaker Shortened to Ground Ignition ON After Ignition OFF for 10 sec. |
| B2023 | Rear Speaker Shortened to Battery Ignition ON After Ignition OFF for 10 sec. |
| B2024 | Sidecar Speaker Shortened R1.0 Ohm |
| B2025 | Sidecar Speaker Opened R>100 Ohms Tested Once Per Ignition Cycle Ignition ON After Ignition OFF for 10 sec. |
| B2026 | Sidecar Speaker Shortened to Ground Ignition ON After Ignition OFF for 10 sec. |
| B2027 | Sidecar Speaker Shortened to Battery Ignition ON After Ignition OFF for 10 sec. |
Sensors and motorHarley-Davidson Fault Code Abbreviations
Sensors and motor
ABS – Anti-Lock Braking System
ACR – Automatic Compression Release
AFR – Air Fuel Ratio
AIS – Active Intake Solenoid
ATS – Air Temperature Sensor
BAS – Bank Angle Sensor
BCM – Body Control Module
CAN – Controller Area Network
CCM – Cruise Control Module
CKP – Crank Position Sensor
DLC – Datalink Connector
DTC – Diagnostic Trouble Codes
ECM – Electronic Control Module
ECT – Engine Coolant Temperature
ECU – Electronic Control Unit
EFI – Electronic Fuel Injection
EFP – Electronic Fuel Pump
ET – Engine Temperature sensor
FI – Fuel Injectors
FPR – Fuel Pressure regulator
H-DSSS – Harley-Davidson Smart Security System
HCU – Hydraulic Control Unit, ABS
[/stag_one_half][stag_one_half_last] HFSM – Hands Free Security Module
HO2S – Heated Oxygen Sensor
IAC – Idle Air Control actuator
IAT – Intake Air Temperature sensor
ICM – Ignition Control Module
IMAP – MAP + IAT in one unit
ISS – Ion Sensing System
JSS – Jiffy Stand Sensor
LHCM – Left Hand Control Module
MAP – Manifold Absolute Pressure Sensor
MHR – Right Hand Control Module
RCM – Reverse Control Module
TCA – Throttle Control Actuator
TGS – Twist Grip Sensor
TMAP – Intake Air Temperature / Manifold Absolute Pressure equipment
TPS – Throttle Position Sensor
TSM / TSSM – (Turn Signal / Turn Signal Security Module)
VE – Volume Efficiency
VIN – Vehicle identification number
VSS – Vehicle Speed Sensor
WSS – Wheel Speed Sensor