Ошибка find file failed

Similar Questions

• Realtek network controller Not found. If hibernation mode, please plug the cable

  I had this error before. I understand that it is the controller not to wake computer recovery. At the time where it happened the first time (several months ago) I accepted it as being dead. 3 days ago, I decided to update my drivers, including the network driver and like magic, my internet works again. I went to bed last night, (do not remember if I tried to shut down my computer) and came this morning to the screen stuck on the screen saver. After a hard reset, I’m back in the same boat. This error appears when I try to repair/reinstall the Realtek Ethernet Controller driver. Windows repair thing when I click on the currently connected to comes up with cannot find a network card or something similar.

  THINGS I’VE TRIED (in every imaginable command):

  -Disconnect the power supply for 30 minutes

  -Remove the CMOS battery for 30 minutes

  -Remove my RAM for 30 minutes (with the CMOS battery and separately)

  Reinstall/Repair of the driver

  -Reset the default bios settings

  -Hit my head several times on the table

  Implies that I agree that the map was dead was fine, until it worked magically for a day. Any help would be highly appreciated!

  Hey you,.

  This may remind you note the virtual applications

  If you use windows 10, note components Hyper-V or virtual of other applications installed on your PC or not

  a virtual network adapter connection may be the reason for the main question

  Guide to remove Hyper-V: Panel-online programs & => turn Windows features on or off features => remove Hyper-V

  Hope this helpful

  

• «Realtek network controller is not found» — various measures already taken

  Hello

  GA B75M — D3H Mobo rev 1.1

  Windows 7 Home Premium SP1

  Intel Core i5 — 3570 k @ 3.40 GHZ processor.

  16 GB GSkill ram

  There is no «network card» listed in Device Manager more. I turned it on and it was gone and a not to connect to anything. No other material changes, no software changes, no damage.

  I selected «Show hidden devices», he showed «Realtek PCIe GBE Family Controller». Disable was gray and under properties it says that this device does not work correctly because it is not connected.

  I read online and decided to uninstall the driver with the hope that by restarting the computer would work. He did not. I reinstalled the driver, it says

  The RealTek network adapter/controller was not found.
  If the active deep sleep Mode please connect the cable

  I had initially it say «Findfile failed» but I fixed using separate drivers instead of the ones on my motherboard drivers CD.

  I have:

  Tried to reinstall the drivers.

  «The RealTek network adapter/controller is not found.
  If Deep Sleep Mode please connect the cable»

  Power off the PC, remove the battery CMOS and RAM, power cord unplugged and waited 45 min, pressed the power button, replaced the RAM, the Cmos battery and power cord and return the computer.

  The BIOS to the default value of the optimized parameters.

  Updated the Bios of the site of gigabytes using @Bios. This has been a success, but has not fixed the problem.

  Check the BIOS of the controller. Under device it lists ‘Lan Controller #1’. It has been activated. I disabled started, stop and enabled and started. Not more than anything.

  I installed the Realtek Ethernet diagnostic utility — it shows that nothing there so he could diagnose.

  I updated the drivers for chipset provided by Gigabyte and I updated the Intel Management Engine Interface. These were both successful, but has not fixed the problem.

  Note: I don’t have anything that is listed under «Network adapters» in the Device Manager. Viewing hidden devices shows a variety of things listed here as «WAN Miniport» and «Card Microsoft 6to4», but none of these are a real network card.

  System Restore is not an option. Thanks for your help.

  Richard

  I don’t think that you had corrected the post as the answer. People with the power to do have a bad habit of marking messages as the answer, particularly when the poster is an engineer/Microsoft, when clearly the question was not answered at all.  You may be able to uncheck the post that you are the original poster. You actually answered your own question, and it must be marked as the answer.

  See you soon

• Windows 7 network drive mapping error: «error code: 0 x 80070035 the network path was not found.»

  I recently started getting an error when you try to access my network drive. Attempt to fix I have also disconnected the drive and tried to reconnect. I get the error: error code: 0 x 80070035 the network path was not found

  I am able to map the drive of all the other machines in the hold of the House (Mac OS X, Windows XP, Windows Vista).  However, the Windows 7 machine continues to report the error.

  I searched the internet for the microsoft Web site and answers and so far nobody seems to have an answer to the problem (and it seems to be a very common problem in Windows 7, based on the number of reports I’ve met in my search). I’m able to reach the reader through the IP address, but cannot connect in it (continues to re — ask for credentials and I checked the credentials I use are 100% correct).

  The only significant event was the address IP changed on the remote disk. What that tells me, is that windows is not updated the name of the drive to the new IP address and confounds seriously on how to get the player passing the correct credentials.

  I removed the protection against viruses (a suggestion said it was the cause), but it has no effect. Check my sharing permissions and so many different places that I could, but nothing has changed and all seems OK.

  The problem is in Windows 7, but I don’t know where all configurations «tricks» are on the (64 bit) OS — has been used for a 32-bit system. Where can I manually fix the DNS or DHCP parameter for the name of the drive?

  SOLUTION

  It’s a problem with Windows Explorer in Windows 7 do not resolve the computer name target to its IP address. It is not a problem with the firewall or antivirus.

  There is a simple workaround solution.  Use the IP address of the target computer, not the computer name.

  (1) find IP address that the computer target is.  It is desirable to give a private static IP address to the target computer, for example, 192.168.1.10, so it does not change.  Use the local windows help when you sit in front of the target computer to do this, if you don’t know how.

  (2) when you are sitting in front of the Windows 7 computer, you want to access the target computer, open Windows Explorer and in the address bar type——followed\192.168.1.10 static address of the target computer, for example, and press enter

  If the target computer uses the name of user and password sharing, after a few seconds, you will be prompted credentials.  Enter the same username and password used to log on the target computer when you’re sitting in front of it.

  The target computer will be added to the list of computer network Windows 7, appearing as an IP address instead of a computer name.  You can access his actions as if it was listed by name instead of the number.

  That’s all.

• You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. The network path was not found. »

  What does this message mean? I get when I click on the icon to evaluate files on another of our computers. «You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. The network path was not found. »

  The other computer has not been configured to allow remote access to this folder from your account.  You’ll want to go to this other computer, right click on the folder that is shared and go to properties, then set the appropriate security settings to allow access.

• Cannot access the network drive or impossible to mount the network drive. Error «network path was not found.

  Original title: network path was not found

  HI, after the upgradation from windows xp sp2 to sp3 (next to the customer) I can’t access the network drive or impossible to mount the network drive. ‘ ‘ It showa error «network path was not found.

  Hi gauravadavadkar,

  Thanks for posting your query in Microsoft Communities. Provide the following information:

  ·         Did you do changes on the computer before the show?

  ·         What is the full error message?

  ·         Work on a domain?

  Follow these methods.

  Method 1: Temporarily disable the security software.

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2: Follow these steps:

  Step 1: Start the computer in safe mode with networkand check if the problem persists.

  S tep 2: if the problem does not persist in safe mode with networking, perform a clean bootto see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow the steps to configure Windows to use a Normal startup state section of the article to start the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Startand then click run.

  (b) type msconfigand click OK.
  The System Configuration utility dialog box appears.

  (c) click on the general tab, click Normal Startup — load all device drivers and services, and then click OK.

  (d) when you are prompted, click restart to restart the computer.

  Method 3: Follow the steps in the article.

  How to troubleshoot a network home in Windows XP

  In Windows network connection issues

  You can read this article for more information:

  Windows wireless and wired network connection problems

  I hope this helps. Let us know if you need more assistance.

  Thank you.

• system failed because iertutil.dll was not found.

  When you start windows xp pro starts then stops and says this application has failed because iertutil.dll was not found.

  When you see a message like this:

  Explorer.EXE — unable to locate component: this application has failed to start because iertutil.dll was not found. Reinstalling the application may fix this problem.

  It is in the case Log:

  Event type: Information
  Event source: Application Popup
  Event category: no
  Event ID: 26
  Date: 18/02/2010
  Time: 08:38:48
  Description:
  Application popup: Explorer.exe — Unable to locate component: this application has failed to start because iertutil.dll was not found.  Reinstalling the application may fix this problem.

  The iertutil.dll file is required for explorer.exe at startup.  If explorer.exe is not able to run, you will not be able to do much with your system until the file is replaced.

  The file may have been deleted accidentally, malicious software could have deleted or your anti-malware software could have been quarantined it thinking it was a threat.

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  First of all, here are all the things you can ‘try’ which do not work:

  sfc/scannow

  The iertutil.dll is not one of the files that are protected by Windows File Protection, so it will not be replaced automatically if it’s missing 3498.  This means that sfc/scannow won’t help you.

  It is also not on your XP installation for you CD to copy or develop.

  You will have the same problem trying to start in any Safe Mode.

  You will not be able to run a browser on the system afflicted to go on Internet download one.  There is also a computer big security risk when downloading files from Internet sites anyway.

  You can still use the Task Manager to run the system restore and back, but I’ve never tried.

  If iertutil.dll is missing, you can copy from a system that works in the system afflicted with the same version of XP and Internet Explorer or sometimes copy one from another location on your system.

  You can get a good copy and put it on a floppy disk, thumb drive etc and copy it to your system plagued by using Manager tasks.

  When you see the error, you can click beyond it and eventually arrived at your screen background image where you can press CTRL-ALT-DEL to start Task Manager. TM you can click file, new task, browse and edit the menu drop-down «Files of type» to all files that you can see all the files in all the folders.

  Browse/navigate to c:windowssystem32 if iertutil.dll is really missing. If the error appears again while browsing, click OK to get past it.  The explorer.exe tries to run and cannot until the missing file is replaced.

  Then, still using the Task Manager, go to the c:windowssystem32dllcache and see if there is a copy of the file.

  If this isn’t in c:windowssystem32dllcache, it is going to be elsewhere on your system and you will find another way.
  Start by looking in c:windowssystem32dllcache.

  If it’s the only thing missing, you can just copy the file to the c:windowssystem32dllcache and paste it into c:windowssystem32 where it belongs.  If you don’t, get one from a working system of the same type as yours, copy to a Flash DRIVE or a floppy disk and always using TM, browse, copy and paste it where it should be.

  TM, you can always access your thumb or other media same diskettes by navigation, copy, paste, etc. all work fine.

  You use TM to navigate to your thumb or floppy disk, copy the iertutil.dll good and then paste it in the c:windowssystem32 folder, where it is supposed to be.

  When go you there once again, your system may still be affected so no matter what you use for malware protection.
  follow these steps:

  Download, install, update and do a full scan with these free malware detection programs:

  Malwarebytes (MMFA): http://malwarebytes.org/
  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/

  It can be uninstalled later if you wish.

  Do not guess what the problem might be — understand and resolve it. I need YOUR voice and the points for helpful answers and propose responses. I’m saving for a pony!

• Error code: 0 x 80070035 the network path was not found.

  Hi all

  I have 2 systems. In one system, I installed Windows XP Pro SP2 and in another machine I installed Windows Vista Home Basic Edition. The two systems are networked. I am able to access and view the shared folder in Vista the XP system. But when I am trying to access folders in XP since Vista I get the below error:

  Windows cannot access \hyd02

  Check the spelling of the name. Otherwise, there could be a problem with your network. In an attempt to identify and solve network problems, click on diagnose.

  Error code: 0 x 80070035 the network path was not found.

  I did the settings below:

  (1) file and printer sharing are enabled in both systems.

  (2) firewall is disabled in the systems.

  (3) in the center of security and network, the network is private.

  and network discovery is enabled, file sharing is enabled, public folder sharing is turned on, printer sharing are enabled and protected by password sharing is

  Off, media sharing turned OFF.

  (4) the name of the task force in both the system is the same.

  Can someone help me solve this error…

  Thank you

  Sylvie G

  Hi Sylvie G

  Thanks for posting on Microsoft Answers.

  Are the same username and password on both systems?
  What is the share name you are trying to do on the XP machine?
  Let’s say that the share name is music, you would get to it by typing \hyd02music

  Can you do a Test PING since the Vista PC on the XP PC?
  Go to a command prompt and type ping followed by the IP address of the computer XP

  Please post back the results… Thank you Ken
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• network error 0 x 80070035 that the network path was not found.

  I have problem of network with Win7 pro. When I click on my network folder links to my LAN I geterror 0 x 80070035 the network path was not found.

  The network has been set up for 4 months, it includes 3 PC, so far the only problems have been minor, such that the network links, which restart a system endangered has been necessary to update the network and worked.

  The 2 other PC can see and access each other and see and access PC Win7 Pro troubled, but troubled PC Win7 Pro can even happen to its own network without theerror records 0 x 80070035 the network path is not found, arise.

  After hours of checking, I have found no resolution, but as I restored it the PC several times, sometimes service reappearing for a while.
  In my search for possible causes, I opened the Device Manager with the selected hidden devices, under network adapters and found189 instances of card Microsoft 6to4.
  I don’t have 3 PC’s networked! Anyone know if it is a normal number for Win7 or I found part of an anomaly.

  Any suggestions?

  c.Maresca

  Thank you for your comments.

  In the search for a solution to my problem of network Win7 Pro, that I’ve been on all the settings you mentioned before that I posted my question and no problem, everything is as it is necessary to have a comprehensive network and the network was very good except the occasional missing links, which I described in my original post. The only addition to the configuration of PC from the network has been initially implemented has been automatic updates to update from Ms.

  The good news is that, as I studied it to the maximum, I found 2 messages in the network forum Win7 which combined provided the solution for my problem with the network.

  As I did research on it, I noticed that a lot of people have similar problems of network. I know that there are many reasons of connectivity issues, as well as the solutions are specific problems, but if other users of the network are affected by the problem of multiple card Microsoft 6to4 and local network error 0 x 80070035 that the network path is not found, the solution I found worked for me.

  If you want to see more respond to this stream.

  c.Maresca

• When you try to access an external drive shared by MAC from Windows, I get an error Code: 0 x 80070035 — the network path was not found

  Original title:

  I’m unable to access an external drive that I have connected to a mac on my home network.  I can access all the files on the mac itself, but when I try to connect to the external drive, windows 7 gives the error Code: 0 x 80070035 — the network path was not found.  The external drive is set to share on the Mac, but Windows 7 always gives me error.

  Hi Comicsancturn,

  Follow the troubleshooting steps in this thread to solve the error 0 x 80070035.

  Let us know if that helps.

• Error code 0 x 80070035 that the network path was not found.

  OT: error code 0 x 80070035
  My wife and I have 3 computers all running Win 7 64 bit. Two jobs and the third is a laptop. My desktop or laptop computer I can access any folder of each machine. However, when I try to click on my wife under ‘Network’ computer I get the message «Windows cannot access\wife_desktop.» When I click ‘See details’ it displays «error code 0 x 80070035. The network path was not found. «I’m running out of things to try.  I tried to use my desktop computer and notebook to help me check the installation on my wife’s computer. I have updated owner and security settings in both car and system, as well as temporarily disable the firewall. Any suggestions would be greatly appreciated.

  Hello

  Method 1: Run the network troubleshooter and check out what he has to say.

  See the links below:
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7
  http://Windows.Microsoft.com/en-us/Windows7/open-networking-troubleshooters
  http://Windows.Microsoft.com/en-us/Windows7/use-Network-Troubleshooter-event-logs-to-solve-network-problems

  Make sure network discovery is enabled on the laptop computer, by default the State network discovery is disabled. If network discovery is off, please take the following steps to turn on.

  (a) click Start.
  (b) click on Control Panel.
  (c) click on network and sharing Center.
  (d) click on the arrow to drop down next to the network discovery.
  (e) click on the option, turn on network discovery.
  (f) click on apply.
  http://Windows.Microsoft.com/en-us/Windows7/enable-or-disable-network-discovery

  Method 2: The question can be caused also by your security program such an antivirus or a firewall of Windows /Defender that can have conflicting parameters as to not not to perform certain tasks. I suggest you temporary disable antivirus and firewall and check the result again. You must activate new security that you was disabled programs.

  http://Windows.Microsoft.com/en-us/Windows7/turn-Windows-Firewall-on-or-off 
  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  See the following link: http://social.technet.microsoft.com/Forums/nb-NO/w7itpronetworking/thread/028a3d13-f571-49e0-abe7-1ca61fb92082

• Network Controller is not found»error message appears in the DEVICE MANAGER

  Hello! I installed WIN 7 Prof 64 bit on my laptop Compaq Presario CQ62-410US and Device Manager shows that the ETHERNET CONTROLLER is not installed correctly. I’ve been using the appropriate drivers:

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4063&LC=en&cc=us&DLC=en&sw_lang=&product=5048…

  I tried to find a solution here:

  http://support.HP.com/us-en/document/c02592699

  «But the» ‘LAN Power Saving ‘ option of «System Configuration ‘ component is missing.

  I uninstalled installed new driver LAN wireless with no result.

  Thank you very much for your help! Miron

  Hello:

  See if it works… Now, it’s to install the Ethernet controller (wired), not the wireless network controller.

  Make sure that you have installed the first Intel chipset driver, then restart.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-87204-1&cc=us&DLC=en&LC=en&OS=4063&product=5048735&sw_lang=

  Then install the ethernet driver second on the list at the link below:

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=14&PFID=7&level=5&Conn=4&DownTypeID=3&GETDOWN=false

• network controller wireless not found in win7 hp 15-g020ca

  The wireless controller does not work and has a yellow! in the Device Manager. Win7 has no idea what it is. No driver info appears and nothing is found when driver update is run.

  It is definitely a software problem I can get this works well if I boot from a CD live linux.

  Computer: hp 15-g020ca

  Driver page: downloads of software & driver HP 15-g020ca Notebook PC | HP® support

  (There is nothing there for a wireless card).

  Any suggestions on getting wireless work?

  Hello:

  You find the parts list for your laptop that the wireless adapter is a WiFi of Atheros AR9485 802.11b/g/n 1 x 1 adapter

  Please see if this driver works for you:

  http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3DswItem%253Dob_128686_1&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

• An error occored while reconnecting to Z: at \BRENLEEBOLINPublic. Microsoft Windows network: the network path was not found. This connection has not been restored,

  A can not access my respect (z), on my Microsoft Windows network, the network path is not found, the connection has not been restored.

  The PC called BrenLeeBolin is actually shot?  It is physically on the network?  Can you go to the BrenLeeBolin PC and see if the Z: drive is actually still there and readable / write?

• «Gateway router not found» error when you try to connect the TiVO DVR with DLink router.

  Original title: gateway router not found

  try to connect the tivo series 2 to the internet with dlink router that he used to work with previous tivo but not with tivo now, it says gateway router not found
  However, my laptop works fine with the router, I tried tivo support nothing helps, too, if I use the phone line works of tivo, but do not store a lot and is running out of room so it will not work fo rme, helllpppppppp thanks

  Hello

  Where exactly you get this error message?

  See the troubleshooting suggested in «Network error message N07 or C107» steps from this link.

  If you try to connect the tivo series 2 to the internet with dlink router then check out the link below:

  http://support.TiVo.com/app/answers/detail/A_ID/400

  Please contact the manufacturer.