Ошибка ман тга едс 03751 05

Коды ошибок MAN часть 9

03600.TRON… No ignition — Too many unsuccessful start attempts

(operation interlock)

03600.ZBR2…………. Fill level, clutch fluid

03601.CNG………. Output stage starter control

03601.EBS.. System bus, monitoring of the axle modulator drive axle

messages by central brake unit; CAN brake

03601.OBDU….Front axle above technically permitted axle load

03601.TRON….. Overheating — Hardware threshold exceeded

in control unit (operation interlock)

03602.EBS…….System bus, monitoring of the axle modulator

additional axle messages by central brake unit;

CAN brake

03602.OBDU…..Rear axle above technically permitted axle load

03602.TRON……. Overheating — Too many overheatings or

hardware threshold exceeded in control unit

(operation interlock)

03602.ZBR2………… Reversing light relay

03603.EBS…System bus, monitoring of the vehicle dynamics

control messages by central brake unit

03603.TRON…..Overheating sensor — Permitted difference from

flame sensor exceeded

(redundant overheating monitoring)

03603.ZBR2………..Heating, Kongsberg circuit

03604.EBS….System bus, monitoring of the steering angle

sensor messages by central brake unit

03604.ZBRO………..Clutch brake shut-off

03605.ZBRO………..Clutch brake shut-off

03606.ZBRO………..Clutch brake shut-off

03607.ZBRO………… Clutch brake shut-off check

03608.ZBRO………….. Clutch brake direct

03609.ZBRO……… Clutch brake direct stage 1

03610.EBS…System bus, monitoring of the central brake unit

messages by axle modulator drive axle; CAN brake

03610.ZBRO……… Clutch brake direct stage 2

03611.ZBRO……… Clutch brake direct stage 3

03612.EBS.. System bus, monitoring of the axle modulator additional

axle messages by axle modulator drive axle

03612.OUZBRO…………. Gearbox neutral

03612.ZBRO………….. Gearbox neutral

03613.EBS_K1 …System bus, monitoring of the electronic stability

program messages by axle modulator drive axle

03613.ZBRO…………. Current gear (T-CAN)

03614.ZBRO………..Gear engaged (T-CAN)

03615.ZBRO…………..Selected gear

03616.ZBRO…………… Gear oil too hot

03617.ZBRO…………… Gear oil too hot

03618.ZBRO……………. Reversing light

03619.ZBRO…………. Reverse light left

03620.EBS….. System bus, monitoring of the central brake

unit messages by axle modulator additional axle

03620.ZBRO…………… Reverse light right

03621.EBS.. System bus, monitoring of the axle modulator drive axle

messages by axle modulator additional axle

03621.ZBRO…………Gearbox activation (T-CAN)

03622.ZBRO…………. EK shut-off Voith

03623.EBS… System bus, monitoring of the vehicle dynamics control

messages by axle modulator additional axle

03623.ZBRO………… Neutral at standstill ZF

03624.ZBRO……..UDS accident data box reversing light

03625.ZBR2…………..Off-road range

03626.ZBRO………… Reversing light buzzer

03627.ZBRO…………… Gear enable Voith

03628.ZBRO…………. Gearbox oil temperature

03629.ZBR2……….. Transfer case neutral

03630.EBS….. System bus, monitoring of the central brake

unit messages by vehicle dynamics control

03631.EBS…….System bus, monitoring of the axle modulator

drive axle messages by vehicle dynamics control

03632.EBS…….System bus, monitoring of the axle modulator

additional axle messages by vehicle dynamics control

03634.EBS….System bus, monitoring of the steering angle

sensor messages by electronic stability program

03650.EBS……………CAN trailer interface

03651.EBS……… CAN trailer interface, CAN high

03652.EBS………..CAN trailer interface, CAN low

03671.EDC ………..Error when reading in EEPROM

03672.EDC ……..Error when reading in the fault memory

03673.EDC ………….. CAN block 2

03674.EDC ………. FFR1: Bank shut-off byte8/bit5-8

03675.EDC …. Faulty redundant shut-off device afterrun drive

03676.EDC …… Faulty redundant shut-off device afterrun test

03677.EDC …….. Charge air low pressure sensor

03678.EDC …………. Booster voltage bank 1

03679.EDC …………. Booster voltage bank 2

03680.EDC ……… Current high pressure pump CP3

03681.EDC ………….. Starter output stage

03682.EDC ……….. Averaged control rod position

03683.EDC … Signalling of activation request for output stage

03684.EDC ………Starter output stage monitoring

03685.EDC …………Activation pulse duty ratio for

exhaust gas recirculation valve

03686.EDC … Activation pulse duty ratio for boost pressure control

03687.EDC …………. Pressure relief valve

03688.EDC …… Pressure controller variable (pulse duty ratio)

03689.EDC ……….. Rail pressure control differential

03690.EDC …………Synchronisation state

03691.EDC ……Current equivalent of clock-pulse ratio

03692.EDC …………recorded filtered temperature

03693.EDC …………. Booster voltage

03694.EDC ……… Timeout message position 4

03700.ZBRO…………….Retarder active

03701.EBS………. Vehicle dynamics control module

03701.ZBRO………. Retarder torque gearbox (T-CAN)

03702.EDC ………..CAN A block DPRAM error

03702.ZBRO…..Retarder torque engine control (T-CAN)

03703.EDC …………CAN A block error passive

03703.ZBRO……….. Retarder activation (T-CAN)

03704.ZBRO…………Retarder off (switch)

03705.EBS……….Vehicle dynamics control system,

EEPROM parameter setting

03705.ZBRO…………Retarder off (button)

03706.EBS…….Installation, vehicle dynamics control module,

vehicle adaptation

03706.ZBRO…………….. Retarder off

03707.EBS..Ensure the ESP components are installed correctly

and calibrate the steering angle sensor

03707.ZBRO…………….. Retarder off

03708.ZBRO……………Retarder off check

03709.ZBRO………… Engine brake off (switch)

03710.ZBRO………… Engine brake off (button)

03711.EDC …………..CAN B block bus off

03711.ZBRO…………..Engine brake off

03712.EDC ………..CAN B block DPRAM error

03712.ZBRO…………..Engine brake off

03713.ZBRO……….. Engine brake off check

03720.EBSVehicle dynamics control module, electrical power supply

03720.EDC ……. Supply to atmospheric pressure sensor

03721.EDC ……… Supply to fuel pressure sensor

03722.EDC …..Supply to charge air low pressure sensor

03723.EDC …………Supply to oil pressure sensor

03724.EDC ……. Supply to charge air pressure sensor

03726.EDC ……. Supply to fuel low pressure sensor

03730.EBS………… Steering angle sensor

03730.EDC ………Defective classification for initialisation

03731.EBS..Steering angle sensor, voltage transformer signal line

03732.EBS……….Steering angle sensor, calibration

03732.EDC ………Defective classification for initialisation

03733.EBS……Steering angle sensor, parameter setting

03733.EDC …………. High-pressure pump

03734.EBS……… Steering angle sensor, steering ratio

03734.EDC ………….. Pressure control valve

03735.EDC …………. EDC internal temperature

03736.EDC ……….. Output stage shut-off by EDC

03737.EDC …….. Initialisation in master/slave mode

03738.EDC ……. Quantity correction value too great

4-cylinder engine: Cyl. 1;

6-cylinder engine: Cyl. 1;

8-cylinder engine: Master cyl. 1, slave cyl. 5;

10-cylinder engine: Master cyl. 1, slave cyl. 6;

12-cylinder engine: Master cyl. 01, slave cyl. 12

03739.EDC ……. Quantity correction value too great

4-cylinder engine: Cyl. 3;

6-cylinder engine: Cyl. 5;

8-cylinder engine: Master cyl. 2, slave cyl. 7;

10-cylinder engine: Master cyl. 5, slave cyl. 10;

12-cylinder engine: Master 0cyl. 5, slave cyl. 8

03740.EDC ……. Quantity correction value too great

4-cylinder engine: Cyl. 4;

6-cylinder engine: Cyl. 3;

8-cylinder engine: Master cyl. 3, slave cyl. 6;

10-cylinder engine: Master cyl. 2, slave cyl. 7;

12-cylinder engine: Master cyl. 03, slave cyl. 10

03741.EDC ……. Quantity correction value too great

4-cylinder engine: Cyl. 2;

6-cylinder engine: Cyl. 6;

8-cylinder engine: Master cyl. 4, slave cyl. 8;

10-cylinder engine: Master cyl. 3, slave cyl. 8;

12-cylinder engine: Master cyl. 06, slave cyl. 7

03742.EDC ……. Quantity correction value too great

6-cylinder engine: Cyl. 2;

10-cylinder engine: Master cyl. 4, slave cyl. 9;

12-cylinder engine: Master cyl. 2, slave cyl. 11

03743.EDC ……. Quantity correction value too great

6-cylinder engine: Cyl. 4;

12-cylinder engine: Master cyl. 4, slave cyl. 9

03744.EDC …… Highside output stage exhaust gas recirculation

system throttle butterfly

03745.EDC ……. Highside output stage charge air pressure

governing system

03746.EDC …….Highside output stage exhaust gas

recirculation system

03747.EDC ……Highside output stage pressure governing valve

03748.EDC ……… Highside output stage metering unit

high-pressure pump CP3

03749.EDC …. Highside output stage engine air flow sensor flap

03750.EDC ………… Highside output stage RH 07

03751.EDC ……. Highside output stage starter relay

03752.EDC …………Segment encoder (camshaft)

03753.EDC ……… Incremental encoder (crankshaft)

03754.EDC ………Monitoring error when system starts

03755.EDC ……..Plausibility fuel supply pressure

03756.EDC ……… Supply voltage sensor group 3 CY310

03758.EDC …….Send error message slot 2 to partner EDC

03759.EDC …….Send error message slot 3 to partner EDC

03760.EDC …….Send error message slot 4 to partner EDC

03761.EDC …….Send error message slot 5 to partner EDC

03762.EDC …… Timeout of the CAMD_ANA message

03763.EDC ……. Timeout of the CAMD_CMOL message

03764.EDC …. Timeout of the CAMD_CONTROL message

03765.EDC ………Timeout of the CAMD_FFR1 message

03766.EDC ………Timeout of the CAMD_FFR2 message

03767.EDC ………Timeout of the CAMD_FFR3 message

03768.EDC ….. Fault status of the CAMD_INIT message

03769.EDC …… Timeout of the CAMD_Limit message

03771.EDC ……. Master / slave error in reception of

vehicle management computer CAN

03772.EDC ………….. Monitoring terminal 15

03773.EDC ….. Operating mode change error master/slave

03774.EDC …. Temporary CMOL mode of the partner EDC

03775.EDC ……….. Rail pressure monitoring

03776.EDC ……. Excessive positive control differential

(control system cannot compensate for too

low rail pressure)

03777.EDC ……Excessive negative control differential

(control system cannot compensate for too

high rail pressure)

03778.EDC …….Rail pressure: Leakage in overrun conditions

03779.EDC …. Rail pressure: Leakage in quantity compensation

03780.EDC ….. Rail pressure: High controller output when idling

03781.EDC ….. Pressure relief valve open (pressure too high)

03782.EDC ………. Fuel supply pressure dynamic

03783.EDC …… FFR (vehicle management computer) 2:

Bit error max. permitted engine acceleration

03784.EDC …………. Bit error smoke ID

03785.EDC …. Monitoring particle filter/PM catalytic converter

03786.EDC ……..Particulate filter temperature limits

03787.EDC ………..No particulate filter regeneration

03788.EDC ………… Exhaust differential pressure

03789.EDC …….. Exhaust differential pressure sensor

03790.EDC …….Exhaust differential pressure plausibility

03791.EDC ….Exhaust temperature before particulate filter

03792.EDC …. Exhaust temperature sensor before particulate filter

03793.EDC …….Exhaust temperature after particulate filter

03794.EDC … Exhaust temperature sensor after particulate filter

03795.EDC ……..Exhaust gas recirculation throttle butterfly

03796.EDCHighside output stage exhaust gas recirculation system 2

03797.EDC …….. Highside output stage lambda probe

03798.EDC ………. Output stage OBD lamp (MIL)

03799.EDC ……… Highside output stage reserve 01

03800.EDC ……… Highside output stage reserve 02

03800.ZBR2………..Air suspension/ECAS

03801.EDC ……… Highside output stage reserve 03

03801.OBDU……..No engine start for at least 3 weeks

03802.EDC …. Highside output stage stop valve compressed air

03802.OBDU……No engine start for at least 10 weeks

03803.EDC …… Engine CAN transmit error, no message

available in vehicle management computer

03804.EDC ……..Engine CAN receive error, not possible to

receive a message from vehicle management computer

03805.EDC ……..Master/slave CAN communication

disrupted, bus load too high

03806.EDC ……..Master/slave CAN communication

disrupted, receive error

03806.ZBRO………….. Raise bus again

03807.EDC ……… Vehicle management computer sends

invalid value in FFR1 message

03807.ZBRO………….. Raise bus again

03808.EDC ……… Vehicle management computer sends

invalid value in FFR2 message

03809.EDC ……… Vehicle management computer sends

invalid value in FFR3 message

03809.ZBRO……………ECAS malfunction

03810.EDC ……… Vehicle management computer sends

invalid numerical value, date/time error

03810.ZBRO………….ECAS warning

03811.ZBRO…….ECAS governing suppression brake

03812.EDC ……. Particulate filter temperature plausibility

03812.ZBRO…………Kneeling lowering

03813.EDC …………. Starter monitoring

03813.ZBRO…………Kneeling lowering

03814.EDC …..Recording of control unit switch-off duration

03814.ZBRO…………. Kneeling fully lowered

03815.EDC ………….. Exhaust backpressure

03815.ZBRO…………. Kneeling fully lowered

03816.EDC ………..Exhaust backpressure sensor

03816.ZBRO…………. Kneeling raise

03817.EDC …. Permanent system deviation exhaust backpressure

03817.ZBRO…………. Kneeling raise

03818.EDC ………Exhaust backpressure plausibility

03818.ZBRO…………Kneeling, manual/automatic

03819.EDC ………….. CAN block 3

03819.ZBRO…………. Kneeling automatic

03820.EDC …………. Byte monitoring CAN 1

(oil, ambient and air temperature)

03820.ZBRO………..Kneeling automatic check

03821.EDC …………. Byte monitoring CAN 3

(exhaust temperature, AdBlue fill level, AdBlue temperature)

03821.ZBRO……….. Kneeling raise control unit (16)

03822.EDC ……….Time overrun CAN 3, exhaust CAN

03822.ZBRO………. Kneeling emergency raise

03823.EDC …………Misfiring on several cylinders

03823.ZBRO………. Kneeling emergency raise

03824.EDC ………….. Misfiring status master

8-cylinder engine: Cylinder 1;

10-cylinder engine: Cylinder 1;

12-cylinder engine: Cylinder 1

03824.ZBRO……. Kneeling emergency raise prio. 1

03825.EDC ………….. Misfiring status master

8-cylinder engine: Cylinder 2;

10-cylinder engine: Cylinder 5;

12-cylinder engine: Cylinder 5

03826.ZBRO………. Kneeling lower control unit (19)

03827.EDC ………….. Misfiring status master

8-cylinder engine: Cylinder 4;

10-cylinder engine: Cylinder 3;

12-cylinder engine: Cylinder 6

03827.ZBRO………….Kneeling door open

03828.EDC ………….. Misfiring status master

10-cylinder engine: Cylinder 4;

12-cylinder engine: Cylinder 2

03828.ZBRO……… Air suspension reservoir too low

03829.EDC ………….. Misfiring status master

12-cylinder engine: Cylinder 4

03829.ZBRO……… Air suspension reservoir too low

03830.EDC ………….. Misfiring status

4-cylinder engine: Cylinder 1;

6-cylinder engine: Cylinder 1;

slave

8-cylinder engine: Cylinder 5;

10-cylinder engine: Cylinder 6;

12-cylinder engine: Cylinder 12

03830.ZBRO…….v <= 3 km/h and no door interlock

03831.EDC ………….. Misfiring status

4-cylinder engine: Cylinder 3;

6-cylinder engine: Cylinder 5;

slave

8-cylinder engine: Cylinder 7;

10-cylinder engine: Cylinder 10;

12-cylinder engine: Cylinder 8

03831.ZBRO………… v > 3 km/h or door interlock

03832.EDC ………….. Misfiring status

4-cylinder engine: Cylinder 4;

6-cylinder engine: Cylinder 3;

slave

8-cylinder engine: Cylinder 6;

10-cylinder engine: Cylinder 7;

12-cylinder engine: Cylinder 10

03832.ZBRO…………. Moving-off aid

03833.EDC ………….. Misfiring status

4-cylinder engine: Cylinder 2;

6-cylinder engine: Cylinder 6;

slave

8-cylinder engine: Cylinder 8;

10-cylinder engine: Cylinder 8;

12-cylinder engine: Cylinder 7

03833.ZBRO…………. Moving-off aid

03834.EDC ………….. Misfiring status

6-cylinder engine: Cylinder 2;

slave

10-cylinder engine: Cylinder 9;

12-cylinder engine: Cylinder 11

03834.ZBRO……….. Moving-off aid check

03835.EDC ………….. Misfiring status

6-cylinder engine: Cylinder 4;

slave

12-cylinder engine: Cylinder 9

03835.ZBRO…………. Moving-off aid switch-off

03836.EDC ………Lambda probe sensor acquisition

03836.ZBRO…….. Lifting bus above normal level

03837.EDC ………Lambda probe sensor acquisition

03837.ZBRO…….. Lifting bus above normal level

03838.EDC ……Lambda probe internal resistance, physical

03838.ZBRO………….Lowering bus again

03839.EDC ………Lambda probe internal resistance

03839.ZBRO………. Lowering bus below ride height

03840.EDC …………. Oil temperature sensor

03840.ZBRO………. Lowering bus below ride height

03841.EDC ………..Coolant pressure sensor

03841.ZBRO…………. Bus normal level

03842.EDC ……… Coolant pressure plausibility

03842.ZBRO…………ECAS activation (T-CAN)

03843.EDC ……..Coolant temperature plausibility

03843.ZBRO…………Kneeling start interlock

03844.EDC ….Plausibility, temperature ahead of cylinder inlet

03844.ZBRO…. NLA bellows is depressurised (p < 0.3 bar)

03845.EDC ……….Ambient air temperature plausibility

03845.ZBRO…….. Switch off NLA bellows depressurisation

03846.EDC ………. Control unit configuration

03846.ZBRO……Driven axle pressurised (p > 8.4 bar)

03847.EDC ….Charge air temperature sensor ahead of motor

03847.ZBRO……… ECAS malfunction flashing at 1 Hz

03848.EDC ……..Ambient air temperature sensor

03848.ZBRO………ECAS malfunction continuous light

03849.EDC ………..Catalyser not installed

03849.ZBRO………ECAS warning or malfunction 2 Hz

03850.EDC . Position deviation enclosed exhaust gas recirculation

03850.ZBRO………..ECAS warning flashing at 1 Hz

03851.EDC ……Exhaust gas recirculation flap position sensor

03852.EDC ….Exhaust gas recirculation temperature plausibility

03853.EDC ….Permanent system deviation exhaust gas recirculation

03854.EDC ………. EDC internal temperature sensor 2

03855.EDC ………….. Lambda probe system

03856.EDC …………. Lambda probe calibration

03857.EDC ……….Lambda probe communication

03858.EDC ………. Lambda probe temperature

03859.EDC ………Lambda probe temperature calibration

03860.EDC ………….Turbine wheel speed

03861.EDC ………Turbine wheel speed sensor

03862.EDC …….NBF pulses without quantity requests

(redundant control travel monitoring)

03863.EDC ………… Trailing throttle monitoring

03903.ZBR2………….Tank/ fuel level

03904.OBDU……… Reservoir pressure circuit 1 (too low)

03905.OBDU……… Reservoir pressure circuit 2 (too low)

03906.OBDU……… Reservoir pressure circuit 3 (too low)

03907.OBDU……… Reservoir pressure circuit 4 (too low)

03909.OBDU………… Previous circuit defective

03913.OBDU……..ECAM in pneumatic backup, CAN OK

03915.OBDU………..ASR engine governor failure

03918.ZBRO………..Fuel tank almost empty

03919.ZBR2………….. Fill level Gas2

03920.ZBR2………….. Fill level Gas3

---

---

---

---

---

8(8482)611-333

8(917)962-81-27

В 02.02.2016 в 19:10, hard67 сказал:

вот схема запуска

если исключить случай, разобранный выше, и при условии, что после заводки мотор работает нормально, а сам авто работает без проблем, то надо смотреть:

1. если щелкает реле стартера, то надо смотреть тяговое и + по проводу 30000 (толстый, сечением 70квадратов) и провод на массу.

2. если не щелкает, то смотрим что на выходе проводов (вроде белый и коричневый), которые к стартеру на тяговое, при повороте ключа в положение ЗАПУСК. Если там не 24в, значит глюк может быть в разъёме Х2549, находится в области мотора, если и на нем нет 24В, сначала грешим на проводку от Эбу мотора до этого разъёма, потом на сам ЭБУ.

А дальше это уже другая история.

На двух приводах, которые идут на реле напряжение 6 вольт, поворачивая ключ на старт двигателя, происходит скачок до 24,4 и снова падает на 6 вольт. Стартер молчит. Что делать? Где собака закрыта? Реле менять или в проводах дело?

Каталог руководств по обслуживанию и ремонту автомобилей самых популярных марок

© 2022 manuals4car.ru Все права защищены.
При упоминании использовании материалов активная ссылка на manuals4car.ru обязательна.

Коды ошибок по маркам автомобилей

Из чего состоит ошибка

В пятизначных кодах первый знак обозначает принадлежность к системе, в которой обнаружена неисправность:

• Р — неполадки, зафиксированные в работе силового агрегата либо автоматической трансмиссии (АКПП);
• В — неисправности, связанные с функционированием кузовных систем — электрических стеклоподъемников, подушек безопасности Airbag (SRS), центрального замка и т. д.;
• С — коды ошибок в работе шасси или ходовой составляющей транспортного средства;
• U — неисправности, связанные с электрикой или электронным оборудованием, взаимодействием между управляющими модулями, цифровым интерфейсом.

Второй знак обозначает:

• 0 — общая цифра для всех OBD2 кодов;
• 1 или 2 — код производителя транспортного средства;
• 3 — резервая позиция.

Третий знак в комбинации неисправности указывает на тип поломки:

• 1 и 2 — сбои в функционировании систем подачи воздуха либо топлива;
• 3 — неисправности в работе системы зажигания;
• 4 — неполадки, связанные с функционированием систем вспомогательного контроля;
• 5 — сбои в работу элементов системы холостого хода;
• 6 — неполадки, зафиксированные в функционировании электронного блока управления автомобилем или его электролиниями;
• 7 и 8 — неисправности трансмиссионного агрегата.

Последние два знака обозначают порядковый номер неисправности.

Copyright © 2021. Коды ошибок OBD-II с расшифровкой на русском языке — возможные причины, описание и варианты по устранению ошибок.